COLD RELEASE PTFE LIQUID: SAFETY DATA SHEET
Also listed as: Mold Release Liquid, PTFE Based (Hot or Cold)
Refer to the original PDF for tables, figures and page layout.
Page 1\n \nPage 1/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\n59.1.0\n* 1 Identification\n· Product name: Mold Release, Liquid, Hot and Cold, PTFE\n· Part number: 200-10015\n· Application of the substance / the mixture Releasing agent\n· Details of the supplier of the safety data sheet\n· Manufacturer/Supplier:\nAllied High Tech Products Inc.\n16207 Carmenita Road\nUSA-Cerritos, CA, 90703\nUSA\ninfo@alliedhightech.com\n· Information department: Product safety department\n· Emergency telephone number:\nDuring normal opening times: +1 (310) 635-2466\nChemtrec: +1 (202) 483-7616\n2 Hazard(s) identification\n· Classification of the substance or mixture\nGHS07\nAcute Toxicity - Inhalation 4\nH332 Harmful if inhaled.\nSkin Irritation 2\nH315 Causes skin irritation.\nEye Irritation 2A\nH319 Causes serious eye irritation.\nSpecific Target Organ Toxicity - Single Exposure 3 H335 May cause respiratory irritation.\nAquatic Chronic 3\nH412 Harmful to aquatic life with long lasting effects.\n· Label elements\n· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).\n· Hazard pictograms\nGHS07\n· Signal word Warning\n· Hazard-determining components of labeling:\ntrans-dichloroethylene\n2h, 3h-Decafluoropentane\n· Hazard statements\nHarmful if inhaled.\n(Contd. on page 2)\n\n\nPage 2\nPage 2/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Mold Release, Liquid, Hot and Cold, PTFE\n(Contd. of page 1)\n59.1.0\nCauses skin irritation.\nCauses serious eye irritation.\nMay cause respiratory irritation.\nHarmful to aquatic life with long lasting effects.\n· Precautionary statements\nAvoid breathing dust/fume/gas/mist/vapors/spray\nWash thoroughly after handling.\nUse only outdoors or in a well-ventilated area.\nAvoid release to the environment.\nWear protective gloves / eye protection / face protection.\nIf on skin: Wash with plenty of water.\nIF INHALED: Remove person to fresh air and keep comfortable for breathing.\nIf in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.\nCall a poison center/doctor if you feel unwell.\nSpecific treatment (see on this label).\nTake off contaminated clothing and wash it before reuse.\nIf skin irritation occurs: Get medical advice/attention.\nIf eye irritation persists: Get medical advice/attention.\nStore in a well-ventilated place. Keep container tightly closed.\nStore locked up.\nDispose of contents/container in accordance with local/regional/national/international regulations.\n* 3 Composition/information on ingredients\n· Chemical characterization: Mixtures\n· Description: Mixture of the substances listed below with nonhazardous additions.\n· Hazardous components and components with occupational exposure limits:\n156-60-5 trans-dichloroethylene\n Flammable Liquids 2, H225;\n Acute Toxicity - Inhalation 4, H332; Aquatic Chronic 3, H412\n60-66%\n138495-42-8 2h, 3h-Decafluoropentane\n Skin Irritation 2, H315; Specific Target Organ Toxicity - Single Exposure 3, H335; Eye Irritation 2B, H320;\nAquatic Chronic 3, H412\n22-26%\n67-63-0 isopropyl alcohol\n Flammable Liquids 2, H225;\n Eye Irritation 2A, H319; Specific Target Organ Toxicity - Single Exposure 3,\nH336\n6-12%\n· Additional information: The specific chemical identity and/or exact percentage of the composition has been withheld as a trade secret.\n4 First-aid measures\n· Description of first aid measures\n· General information:\nImmediately remove any clothing soiled by the product.\nSymptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.\n· After inhalation:\nSupply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist.\nIn case of unconsciousness place patient stably in side position for transportation.\n· After skin contact: Immediately wash with water and soap and rinse thoroughly.\n· After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.\n· After swallowing: If symptoms persist consult doctor.\n· Information for doctor:\n· Most important symptoms and effects, both acute and delayed\nBreathing difficulty\nDizziness\nCoughing\nNausea\nDermatitis\nEye irritation\n(Contd. on page 3)\n\n\nPage 3\nPage 3/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Mold Release, Liquid, Hot and Cold, PTFE\n(Contd. of page 2)\n59.1.0\n· Indication of any immediate medical attention and special treatment needed No further relevant information available.\n5 Fire-fighting measures\n· Extinguishing media\n· Suitable extinguishing agents:\nCarbon dioxide\nAlcohol resistant foam\nUse fire fighting measures that suit the environment.\n· Special hazards arising from the substance or mixture No further relevant information available.\n· Advice for firefighters\n· Protective equipment: Mouth respiratory protective device.\n6 Accidental release measures\n· Personal precautions, protective equipment and emergency procedures Not required.\n· Environmental precautions:\nDo not allow to enter sewers/ surface or ground water.\nInform respective authorities in case of seepage into water course or sewage system.\n· Methods and material for containment and cleaning up:\nAbsorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).\nDispose contaminated material as waste according to section 13.\nEnsure adequate ventilation.\n· Reference to other sections\nSee Section 7 for information on safe handling.\nSee Section 8 for information on personal protection equipment.\nSee Section 13 for disposal information.\n7 Handling and storage\n· Handling:\n· Precautions for safe handling\nEnsure proper ventilation/exhaustion at workplaces.\nPrevent formation of aerosols.\n· Information about protection against explosions and fires: No special measures required.\n· Conditions for safe storage, including any incompatibilities\n· Storage:\n· Requirements to be met by storerooms and receptacles: Store at temperatures not exceeding 52°C.\n· Information about storage in one common storage facility: Not required.\n· Further information about storage conditions:\nProtect from frost.\nKeep receptacle tightly sealed.\nStore receptacle in a well ventilated area.\n· Specific end use(s) No further relevant information available.\n8 Exposure controls/personal protection\n· Additional information about design of technical systems: No additional data. See 7.\n· Control parameters\n· Components with limit values that require monitoring at the workplace:\nThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.\nAt this time, the remaining constituent has no known exposure limits.\n156-60-5 trans-dichloroethylene\nPEL Long-term value: 790 mg/m³, 200 ppm\nREL Long-term value: 790 mg/m³, 200 ppm\nTLV Long-term value: 200 ppm\n(Contd. on page 4)\n\n\nPage 4\nPage 4/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Mold Release, Liquid, Hot and Cold, PTFE\n(Contd. of page 3)\n59.1.0\n67-63-0 isopropyl alcohol\nPEL Long-term value: 980 mg/m³, 400 ppm\nREL Short-term value: 1225 mg/m³, 500 ppm\nLong-term value: 980 mg/m³, 400 ppm\nTLV Short-term value: 400 ppm\nLong-term value: 200 ppm\nBEI, A4\n· Ingredients with biological limit values:\n67-63-0 isopropyl alcohol\nBEI 40 mg/L\nMedium: urine\nTime: end of shift at end of workweek\nParameter: Acetone (background, nonspecific)\n· Exposure controls\n· Personal protective equipment:\n· General protective and hygienic measures:\nKeep away from foodstuffs, beverages and feed.\nImmediately remove all soiled and contaminated clothing.\nWash hands before breaks and at the end of work.\nAvoid contact with the eyes and skin.\n· Breathing equipment: Use suitable respiratory protective device when high concentrations are present.\n· Protection of hands:\nDue to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.\nProtective gloves\nThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.\nSelection of the glove material on consideration of the penetration times, rates of diffusion and the degradation\n· Material of gloves\nThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer\nto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance\nand has therefore to be checked prior to the application.\n· Eye protection:\nSafety glasses\nTightly sealed goggles\n9 Physical and chemical properties\n· Information on basic physical and chemical properties\n· General Information\n· Appearance:\nForm:\nLiquid\nColor:\nWhite\n· Odor:\nLight\n· Odor threshold:\nNot determined.\n· pH-value at 20 °C (68 °F):\n7 \n· Change in condition\nMelting point/Melting range:\nUndetermined.\n(Contd. on page 5)\n\n\nPage 5\nPage 5/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Mold Release, Liquid, Hot and Cold, PTFE\n(Contd. of page 4)\n59.1.0\nBoiling point/Boiling range:\n48 °C (118.4 °F)\n· Flash point:\nNot applicable.\n· Flammability (solid, gaseous):\nNot applicable.\n· Auto igniting:\n440 °C (824 °F)\n· Decomposition temperature:\nNot determined.\n· Ignition temperature:\nProduct is not selfigniting.\n· Danger of explosion:\nProduct does not present an explosion hazard.\n· Explosion limits:\nLower:\nNot determined.\nUpper:\nNot determined.\n· Vapor pressure at 25 °C (77 °F):\n425.3 hPa (319 mm Hg)\n· Density:\nNot determined.\n· Relative density\nNot determined.\n· Vapor density\nNot determined.\n· Evaporation rate\nNot determined.\n· Solubility in / Miscibility with\nWater:\nNot miscible or difficult to mix.\n· Partition coefficient (n-octanol/water): Not determined.\n· Viscosity:\nDynamic:\nNot determined.\nKinematic:\nNot determined.\n· Solvent content:\nOrganic solvents:\n63.5-75 %\nVOC content:\n63.46-75 %\nSolids content:\n0.0 %\n· Other information\nNo further relevant information available.\n10 Stability and reactivity\n· Reactivity No further relevant information available.\n· Chemical stability\n· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.\n· Possibility of hazardous reactions No dangerous reactions known.\n· Conditions to avoid\nKeep away from oxidising agents and acidic substances.\nDo not mix with alkalis.\nKeep away from heat.\nKeep away from open flames. - No smoking.\nKeep away from alkaline solutions.\n· Incompatible materials: No further relevant information available.\n· Hazardous decomposition products:\nCarbon monoxide and carbon dioxide\nHydrogen chloride (HCl)\nHydrogen fluoride\n· Additional information: Hazardous decomposition products may form during combustion.\n(Contd. on page 6)\n\n\nPage 6\nPage 6/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Mold Release, Liquid, Hot and Cold, PTFE\n(Contd. of page 5)\n59.1.0\n11 Toxicological information\n· Information on toxicological effects\n· Acute toxicity:\n· LD/LC50 values that are relevant for classification:\nATE (Acute Toxicity Estimate)\nInhalative LC50/4 h 17.3-19.1 mg/l\n 156-60-5 trans-dichloroethylene\nOral\nLD50\n7,902 mg/kg (rat)\nInhalative LC50/4 h 11 mg/l (ATE)\n138495-42-8 2h, 3h-Decafluoropentane\nOral\nLD50\n>5,000 mg/kg (rat)\nDermal\nLD50\n>5,000 mg/kg (rabbit)\nInhalative LC50/4 h 114 mg/l (rat)\n67-63-0 isopropyl alcohol\nOral\nLD50\n5,045 mg/kg (rat)\nDermal\nLD50\n12,800 mg/kg (rabbit)\nInhalative LC50/4 h 30 mg/l (rat)\n· Primary chemical irritant effect:\n· on the skin: Irritant to skin and mucous membranes.\n· on the eye: Irritating effect.\n· Sensitization: No sensitizing effects known.\n· Additional toxicological information:\n· Carcinogenic categories\n· IARC (International Agency for Research on Cancer)\n67-63-0 isopropyl alcohol\n3 \n· NTP (National Toxicology Program)\nNone of the ingredients is listed.\n· OSHA-Ca (Occupational Safety & Health Administration)\nNone of the ingredients is listed.\n12 Ecological information\n· Toxicity\n· Aquatic toxicity:\n156-60-5 trans-dichloroethylene\nEC50 (96 h) 798 mg/l (fresh water algae)\nLC50 (96 h) 74 mg/l (bluegill sunfish)\nLC50 (48 h) 79 mg/l (daphnia)\n138495-42-8 2h, 3h-Decafluoropentane\nLC50 (96 h) 27.2 mg/l (fathead minnows)\n13.9 mg/l (rainbow trout)\nLC50 (48 h) 11.7 mg/l (daphnia)\n· Persistence and degradability No further relevant information available.\n· Behavior in environmental systems:\n· Bioaccumulative potential No further relevant information available.\n· Mobility in soil No further relevant information available.\n(Contd. on page 7)\n\n\nPage 7\nPage 7/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Mold Release, Liquid, Hot and Cold, PTFE\n(Contd. of page 6)\n59.1.0\n· Ecotoxical effects:\n· Remark: Harmful to fish\n· Additional ecological information:\n· General notes:\nWater hazard class 2 (Self-assessment): hazardous for water\nDo not allow product to reach ground water, water course or sewage system.\nDanger to drinking water if even small quantities leak into the ground.\nHarmful to aquatic organisms\n· Results of PBT and vPvB assessment\n· PBT: Not applicable.\n· vPvB: Not applicable.\n· Other adverse effects No further relevant information available.\n13 Disposal considerations\n· Waste treatment methods\n· Recommendation: Contact waste processors for recycling information.\n· Uncleaned packagings:\n· Recommendation: Disposal must be made according to official regulations.\n14 Transport information\n· UN-Number\n· DOT, ADN, IMDG, IATA\nnot regulated\n· UN proper shipping name\n· DOT, ADN, IMDG, IATA\nnot regulated\n· Transport hazard class(es)\n· DOT, ADN, IMDG, IATA\n· Class\nnot regulated\n· Packing group\n· DOT, IMDG, IATA\nnot regulated\n· Environmental hazards:\n· Marine pollutant:\nNo\n· Special precautions for user\nNot applicable.\n· Transport in bulk according to Annex II of MARPOL73/78 and\nthe IBC Code\nNot applicable.\n· UN "Model Regulation":\nnot regulated\n15 Regulatory information\n· Safety, health and environmental regulations/legislation specific for the substance or mixture\nNo further relevant information available.\n· Sara\n· Section 355 (extremely hazardous substances):\nNone of the ingredients is listed.\n· Section 313 (Specific toxic chemical listings):\n67-63-0 isopropyl alcohol\n· TSCA (Toxic Substances Control Act):\nAll components have the value ACTIVE.\n· Hazardous Air Pollutants\nNone of the ingredients is listed.\n(Contd. on page 8)\n\n\nPage 8\nPage 8/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Mold Release, Liquid, Hot and Cold, PTFE\n(Contd. of page 7)\n59.1.0\n· Proposition 65\n· Chemicals known to cause cancer:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for females:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for males:\nNone of the ingredients is listed.\n· Chemicals known to cause developmental toxicity:\nNone of the ingredients is listed.\n· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.\n16 Other information\nTo the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties\nand does not establish a contractual legal relationship.\n· Department issuing SDS: Technical Services\n· Contact: Pablo Mendoza\n· Last revision / supersedes version: 06/01/2024 / 3.0\n· Supersedes date: 06/01/2024\n· Abbreviations and acronyms:\nADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by\nRoad)\nIMDG: International Maritime Code for Dangerous Goods\nDOT: US Department of Transportation\nIATA: International Air Transport Association\nEINECS: European Inventory of Existing Commercial Chemical Substances\nELINCS: European List of Notified Chemical Substances\nCAS: Chemical Abstracts Service (division of the American Chemical Society)\nVOC: Volatile Organic Compounds (USA, EU)\nLC50: Lethal concentration, 50 percent\nLD50: Lethal dose, 50 percent\nPBT: Persistent, Bioaccumulative and Toxic\nvPvB: very Persistent and very Bioaccumulative\nOSHA: Occupational Safety & Health\nTLV: Threshold Limit Value\nPEL: Permissible Exposure Limit\nREL: Recommended Exposure Limit\nBEI: Biological Exposure Limit\nFlammable Liquids 2: Flammable liquids – Category 2\nAcute Toxicity - Inhalation 4: Acute toxicity – Category 4\nSkin Irritation 2: Skin corrosion/irritation – Category 2\nEye Irritation 2A: Serious eye damage/eye irritation – Category 2A\nEye Irritation 2B: Serious eye damage/eye irritation – Category 2B\nSpecific Target Organ Toxicity - Single Exposure 3: Specific target organ toxicity (single exposure) – Category 3\nAquatic Chronic 3: Hazardous to the aquatic environment - long-term aquatic hazard – Category 3\n· * Data compared to the previous version altered. \n