COLD RELEASE SPRAY: SAFETY DATA SHEET
Also listed as: Mold Release Spray (Cold Mounting)
Refer to the original PDF for tables, figures and page layout.
Page 1\n \nPage 1/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\n59.1.0\n* 1 Identification\n· Product name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n· Part number: 200-10011\n· Details of the supplier of the safety data sheet\n· Manufacturer/Supplier:\nAllied High Tech Products Inc.\n16207 Carmenita Road\nUSA-Cerritos, CA, 90703\nUSA\ninfo@alliedhightech.com\n· Information department: Product safety department\n· Emergency telephone number:\nDuring normal opening times: +1 (310) 635-2466\nChemtrec: +1 (202) 483-7616\n2 Hazard(s) identification\n· Classification of the substance or mixture\nGHS02 Flame\nFlammable Aerosols 1\nH222 Extremely flammable aerosol.\nGHS04 Gas cylinder\nGases under Pressure - Compressed gas H280 Contains gas under pressure; may explode if heated.\nGHS08 Health hazard\nGerm Cell Mutagenicity 1B\nH340 May cause genetic defects.\nAspiration Hazard 1\nH304 May be fatal if swallowed and enters airways.\nGHS07\nAcute Toxicity - Inhalation 4\nH332 Harmful if inhaled.\nAquatic Chronic 3\nH412 Harmful to aquatic life with long lasting effects.\n· Label elements\n· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).\n(Contd. on page 2)\n\n\nPage 2\nPage 2/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n(Contd. of page 1)\n59.1.0\n· Hazard pictograms\nGHS02\nGHS04\nGHS07\nGHS08\n· Signal word Danger\n· Hazard-determining components of labeling:\nPetroleum gases, liquefied, sweetened\nNaphtha (petroleum), light alkylate\n· Hazard statements\nExtremely flammable aerosol.\nContains gas under pressure; may explode if heated.\nHarmful if inhaled.\nMay cause genetic defects.\nMay be fatal if swallowed and enters airways.\nHarmful to aquatic life with long lasting effects.\n· Precautionary statements\nObtain special instructions before use.\nDo not handle until all safety precautions have been read and understood.\nKeep away from heat/sparks/open flames/hot surfaces. - No smoking.\nDo not spray on an open flame or other ignition source.\nPressurized container: Do not pierce or burn, even after use.\nAvoid breathing dust/fume/gas/mist/vapors/spray\nUse only outdoors or in a well-ventilated area.\nAvoid release to the environment.\nWear protective gloves/protective clothing/eye protection/face protection.\nIf swallowed: Immediately call a poison center/doctor.\nDo NOT induce vomiting.\nIF INHALED: Remove person to fresh air and keep comfortable for breathing.\nIF exposed or concerned: Get medical advice/attention.\nCall a poison center/doctor if you feel unwell.\nStore locked up.\nProtect from sunlight. Store in a well-ventilated place.\nProtect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.\nDispose of contents/container in accordance with local/regional/national/international regulations.\n3 Composition/information on ingredients\n· Chemical characterization: Mixtures\n· Description: Mixture of the substances listed below with nonhazardous additions.\n· Hazardous components and components with occupational exposure limits:\n68476-86-8 Petroleum gases, liquefied, sweetened\n Flammable Gases 1, H220;\n Gases under Pressure - Compressed gas, H280;\n Germ Cell Mutagenicity 1B,\nH340; Carcinogenicity 1A, H350\n25-35%\n64741-66-8 Naphtha (petroleum), light alkylate\n Germ Cell Mutagenicity 1B, H340; Carcinogenicity 1B, H350; Aspiration Hazard 1, H304\n8-12%\n9007-48-1 Plurol oleique\n Skin Irritation 2, H315; Eye Irritation 2A, H319\n1-5%\n63148-62-9 siloxane\n Aquatic Chronic 2, H411\n1-5%\n· Non-hazardous components:\n7732-18-5 water, distilled, conductivity or of similar purity\n50-60%\n(Contd. on page 3)\n\n\nPage 3\nPage 3/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n(Contd. of page 2)\n59.1.0\n4 First-aid measures\n· Description of first aid measures\n· General information:\nSymptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.\n· After inhalation:\nSupply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist.\nIn case of unconsciousness place patient stably in side position for transportation.\n· After skin contact: Generally the product does not irritate the skin.\n· After eye contact: Rinse opened eye for several minutes under running water.\n· After swallowing: If symptoms persist consult doctor.\n· Information for doctor:\n· Most important symptoms and effects, both acute and delayed\nBreathing difficulty\nCoughing\n· Indication of any immediate medical attention and special treatment needed No further relevant information available.\n5 Fire-fighting measures\n· Extinguishing media\n· Suitable extinguishing agents: Use fire fighting measures that suit the environment.\n· Special hazards arising from the substance or mixture No further relevant information available.\n· Advice for firefighters\n· Protective equipment: Wear fully protective suit.\n6 Accidental release measures\n· Personal precautions, protective equipment and emergency procedures\nWear protective equipment. Keep unprotected persons away.\nEnsure adequate ventilation\nKeep away from ignition sources\n· Environmental precautions: Inform respective authorities in case of seepage into water course or sewage system.\n· Methods and material for containment and cleaning up:\nDispose contaminated material as waste according to section 13.\nEnsure adequate ventilation.\n· Reference to other sections\nSee Section 7 for information on safe handling.\nSee Section 8 for information on personal protection equipment.\nSee Section 13 for disposal information.\n7 Handling and storage\n· Handling:\n· Precautions for safe handling\nProtect from heat and direct sunlight.\nEnsure proper ventilation/exhaustion at workplaces.\nOpen and handle receptacle with care.\n· Information about protection against explosions and fires: Keep ignition sources away - Do not smoke.\n· Conditions for safe storage, including any incompatibilities\n· Storage:\n· Requirements to be met by storerooms and receptacles: Observe official regulations on storing packagings with pressurized containers.\n· Information about storage in one common storage facility: Not required.\n· Further information about storage conditions:\nKeep receptacle tightly sealed.\nStore receptacle in a well ventilated area.\n· Specific end use(s) No further relevant information available.\n(Contd. on page 4)\n\n\nPage 4\nPage 4/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n(Contd. of page 3)\n59.1.0\n8 Exposure controls/personal protection\n· Additional information about design of technical systems: No additional data. See 7.\n· Control parameters\n· Components with limit values that require monitoring at the workplace:\nThe product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.\n· Exposure controls\n· Personal protective equipment:\n· General protective and hygienic measures:\nKeep away from foodstuffs, beverages and feed.\nWash hands before breaks and at the end of work.\nStore protective clothing separately.\n· Breathing equipment: Use suitable respiratory protective device when high concentrations are present.\n· Protection of hands:\nProtective gloves\nThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.\nSelection of the glove material on consideration of the penetration times, rates of diffusion and the degradation\n· Material of gloves\nThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer\nto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance\nand has therefore to be checked prior to the application.\n· Eye protection:\nSafety glasses\nTightly sealed goggles\n9 Physical and chemical properties\n· Information on basic physical and chemical properties\n· General Information\n· Appearance:\nForm:\nAerosol\nColor:\nWhite\n· Odor:\nLight\n· Odor threshold:\nNot determined.\n· pH-value:\nNot determined.\n· Change in condition\nMelting point/Melting range:\n104-106 °C (219.2-222.8 °F)\nBoiling point/Boiling range:\n0 °C (32 °F)\n· Flash point:\nNot applicable, as aerosol.\n· Flammability (solid, gaseous):\nNot applicable.\n· Decomposition temperature:\nNot determined.\n· Ignition temperature:\nProduct is not selfigniting.\n· Danger of explosion:\nNot determined.\n(Contd. on page 5)\n\n\nPage 5\nPage 5/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n(Contd. of page 4)\n59.1.0\n· Explosion limits:\nLower:\nNot determined.\nUpper:\nNot determined.\n· Vapor pressure at 20 °C (68 °F):\n24 hPa (18 mm Hg)\n· Density at 20 °C (68 °F):\n0.895 g/cm³ (7.469 lbs/gal)\n· Relative density\nNot determined.\n· Vapor density\nNot determined.\n· Evaporation rate\nNot applicable.\n· Solubility in / Miscibility with\nWater:\nNot miscible or difficult to mix.\n· Partition coefficient (n-octanol/water): Not determined.\n· Viscosity:\nDynamic:\nNot determined.\nKinematic:\nNot determined.\n· Solvent content:\nOrganic solvents:\n6.8-10.3 %\nWater:\n51.3 %\nVOC content:\n6.84-10.26 %\nSolids content:\n0.0 %\n· Other information\nNo further relevant information available.\n10 Stability and reactivity\n· Reactivity No further relevant information available.\n· Chemical stability\n· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.\n· Possibility of hazardous reactions No dangerous reactions known.\n· Conditions to avoid No further relevant information available.\n· Incompatible materials: No further relevant information available.\n· Hazardous decomposition products: No dangerous decomposition products known.\n11 Toxicological information\n· Information on toxicological effects\n· Acute toxicity:\n· LD/LC50 values that are relevant for classification:\nOral\nLD50\n41,251.2 mg/kg (not defined)\nDermal\nLD50\n9,562.1 mg/kg (not defined)\nInhalative LC50/4 h 4,121 mg/l (not defined)\n· Primary chemical irritant effect:\n· on the skin: No irritant effect.\n· on the eye: No irritating effect.\n· Sensitization: No sensitizing effects known.\n· Additional toxicological information: The product can cause inheritable damage.\n· Carcinogenic categories\n· IARC (International Agency for Research on Cancer)\nNone of the ingredients is listed.\n· NTP (National Toxicology Program)\nNone of the ingredients is listed.\n(Contd. on page 6)\n\n\nPage 6\nPage 6/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n(Contd. of page 5)\n59.1.0\n· OSHA-Ca (Occupational Safety & Health Administration)\nNone of the ingredients is listed.\n12 Ecological information\n· Toxicity\n· Aquatic toxicity: No further relevant information available.\n· Persistence and degradability No further relevant information available.\n· Behavior in environmental systems:\n· Bioaccumulative potential No further relevant information available.\n· Mobility in soil No further relevant information available.\n· Ecotoxical effects:\n· Remark: Harmful to fish\n· Additional ecological information:\n· General notes:\nDo not allow product to reach ground water, water course or sewage system, even in small quantities.\nDanger to drinking water if even extremely small quantities leak into the ground.\nHarmful to aquatic organisms\n· Results of PBT and vPvB assessment\n· PBT: Not applicable.\n· vPvB: Not applicable.\n· Other adverse effects No further relevant information available.\n13 Disposal considerations\n· Waste treatment methods\n· Recommendation: Contact waste processors for recycling information.\n· Uncleaned packagings:\n· Recommendation: Disposal must be made according to official regulations.\n14 Transport information\n· UN-Number\n· DOT, IMDG, IATA\nUN1950\n· UN proper shipping name\n· DOT\nAerosols, flammable\n· IMDG\nAEROSOLS\n· IATA\nAEROSOLS, flammable\n· Transport hazard class(es)\n· DOT\n· Class\n2.1 Gases\n· Label\n2.1\n· IMDG, IATA\n· Class\n2.1 Gases\n· Label\n2.1\n(Contd. on page 7)\n\n\nPage 7\nPage 7/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n(Contd. of page 6)\n59.1.0\n· Packing group\n· DOT, IMDG, IATA\nnot regulated\n· Environmental hazards:\nNot applicable.\n· Special precautions for user\nWarning: Gases\n· Hazard identification number (Kemler code):\n- \n· EMS Number:\nF-D,S-U\n· Stowage Code\nSW1 Protected from sources of heat.\nSW22 For AEROSOLS with a maximum capacity of 1 litre: Category\nA. For AEROSOLS with a capacity above 1 litre: Category B. For\nWASTE AEROSOLS: Category C, Clear of living quarters.\n· Segregation Code\nSG69 For AEROSOLS with a maximum capacity of 1 litre:\nSegregation as for class 9. Stow "separated from" class 1 except for\ndivision 1.4.\nFor AEROSOLS with a capacity above 1 litre:\nSegregation as for the appropriate subdivision of class 2.\nFor WASTE AEROSOLS:\nSegregation as for the appropriate subdivision of class 2.\n· Transport in bulk according to Annex II of MARPOL73/78 and\nthe IBC Code\nNot applicable.\n· Transport/Additional information:\n· DOT\n· Quantity limitations\nOn passenger aircraft/rail: 75 kg\nOn cargo aircraft only: 150 kg\n· Limited quantities (LQ)\n1L\n· Transport category\n2 \n· Tunnel restriction code\nD \n· IMDG\n· Limited quantities (LQ)\n1L\n· Excepted quantities (EQ)\nCode: E0\nNot permitted as Excepted Quantity\n· UN "Model Regulation":\nUN 1950 AEROSOLS, 2.1\n15 Regulatory information\n· Safety, health and environmental regulations/legislation specific for the substance or mixture\nNo further relevant information available.\n· Sara\n· Section 355 (extremely hazardous substances):\nNone of the ingredients is listed.\n· Section 313 (Specific toxic chemical listings):\nNone of the ingredients is listed.\n· TSCA (Toxic Substances Control Act):\nAll components have the value ACTIVE.\n· Hazardous Air Pollutants\nNone of the ingredients is listed.\n· Proposition 65\n· Chemicals known to cause cancer:\nNone of the ingredients is listed.\n(Contd. on page 8)\n\n\nPage 8\nPage 8/8\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Cold Mounting)\n(Contd. of page 7)\n59.1.0\n· Chemicals known to cause reproductive toxicity for females:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for males:\nNone of the ingredients is listed.\n· Chemicals known to cause developmental toxicity:\nNone of the ingredients is listed.\n· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.\n16 Other information\nTo the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties\nand does not establish a contractual legal relationship.\n· Department issuing SDS: Technical Services\n· Contact: Pablo Mendoza\n· Last revision / supersedes version: 06/01/2024 / 1.0\n· Supersedes date: 10/13/2023\n· Abbreviations and acronyms:\nADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by\nRoad)\nIMDG: International Maritime Code for Dangerous Goods\nDOT: US Department of Transportation\nIATA: International Air Transport Association\nEINECS: European Inventory of Existing Commercial Chemical Substances\nELINCS: European List of Notified Chemical Substances\nCAS: Chemical Abstracts Service (division of the American Chemical Society)\nVOC: Volatile Organic Compounds (USA, EU)\nLC50: Lethal concentration, 50 percent\nLD50: Lethal dose, 50 percent\nPBT: Persistent, Bioaccumulative and Toxic\nvPvB: very Persistent and very Bioaccumulative\nOSHA: Occupational Safety & Health\nTLV: Threshold Limit Value\nPEL: Permissible Exposure Limit\nREL: Recommended Exposure Limit\nFlammable Gases 1: Flammable gases – Category 1\nFlammable Aerosols 1: Aerosols – Category 1\nGases under Pressure - Compressed gas: Gases under pressure – Compressed gas\nAcute Toxicity - Inhalation 4: Acute toxicity – Category 4\nSkin Irritation 2: Skin corrosion/irritation – Category 2\nEye Irritation 2A: Serious eye damage/eye irritation – Category 2A\nGerm Cell Mutagenicity 1B: Germ cell mutagenicity – Category 1B\nCarcinogenicity 1A: Carcinogenicity – Category 1A\nCarcinogenicity 1B: Carcinogenicity – Category 1B\nAspiration Hazard 1: Aspiration hazard – Category 1\nAquatic Chronic 2: Hazardous to the aquatic environment - long-term aquatic hazard – Category 2\nAquatic Chronic 3: Hazardous to the aquatic environment - long-term aquatic hazard – Category 3\n· * Data compared to the previous version altered. \n