EpoxyMount Part A & B
Also listed as: SAFETY DATA SHEET
Refer to the original PDF for tables, figures and page layout.
Page 1\nPage 1/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\n59.1.0\n* 1 Identification\n· Product name: EpoxyMount Resin - Part A\n· Part number:\n145-10005, 145-10020\n145-10010, 145-10025\n· Application of the substance / the mixture Epoxy resin\n· Details of the supplier of the safety data sheet\n· Manufacturer/Supplier:\nAllied High Tech Products Inc.\n16207 Carmenita Road\nUSA-Cerritos, CA, 90703\nUSA\ninfo@alliedhightech.com\n· Information department: Product safety department\n· Emergency telephone number:\nDuring normal opening times: +1 (310) 635-2466\nChemtrec: +1 (202) 483-7616\n2 Hazard(s) identification\n· Classification of the substance or mixture\nGHS09 Environment\nAquatic Chronic 2\nH411 Toxic to aquatic life with long lasting effects.\nGHS07\nSkin Irritation 2\nH315 Causes skin irritation.\nEye Irritation 2A\nH319 Causes serious eye irritation.\nSensitization - Skin 1 H317 May cause an allergic skin reaction.\n· Label elements\n· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).\n· Hazard pictograms\nGHS07\nGHS09\n· Signal word Warning\n(Contd. on page 2)\n\n\nPage 2\nPage 2/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Resin - Part A\n(Contd. of page 1)\n59.1.0\n· Hazard-determining components of labeling:\nreaction product: bisphenol-A-(epichlorhydrin) epoxy resin (number average molecular weight 700)\n· Hazard statements\nCauses skin irritation.\nCauses serious eye irritation.\nMay cause an allergic skin reaction.\nToxic to aquatic life with long lasting effects.\n· Precautionary statements\nAvoid breathing dust/fume/gas/mist/vapors/spray\nWash thoroughly after handling.\nContaminated work clothing must not be allowed out of the workplace.\nAvoid release to the environment.\nWear protective gloves / eye protection / face protection.\nIf on skin: Wash with plenty of water.\nIf in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.\nTake off contaminated clothing and wash it before reuse.\nIf skin irritation or rash occurs: Get medical advice/attention.\nSpecific treatment (see on this label).\nIf eye irritation persists: Get medical advice/attention.\nWash contaminated clothing before reuse.\nCollect spillage.\nDispose of contents/container in accordance with local/regional/national/international regulations.\n3 Composition/information on ingredients\n· Chemical characterization: Mixtures\n· Description: Mixture of the substances listed below with nonhazardous additions.\n· Hazardous components and components with occupational exposure limits:\n25068-38-6 reaction product: bisphenol-A-(epichlorhydrin) epoxy resin (number average molecular weight 700)\n Aquatic Chronic 2, H411;\n Skin Irritation 2, H315; Eye Irritation 2A, H319; Sensitization - Skin 1, H317\n70-80%\n· Non-hazardous components:\n120547-52-6 Aliphatic Glycidyl Ether\n20-30%\n· Additional information: The specific chemical identity and/or exact percentage of the composition has been withheld as a trade secret.\n4 First-aid measures\n· Description of first aid measures\n· General information: Immediately remove any clothing soiled by the product.\n· After inhalation:\nSupply fresh air and to be sure call for a doctor.\nIn case of unconsciousness place patient stably in side position for transportation.\n· After skin contact: Immediately wash with water and soap and rinse thoroughly.\n· After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.\n· After swallowing: If symptoms persist consult doctor.\n· Information for doctor:\n· Most important symptoms and effects, both acute and delayed\nAllergic reactions\nDermatitis\nEye irritation\n· Indication of any immediate medical attention and special treatment needed No further relevant information available.\n5 Fire-fighting measures\n· Extinguishing media\n· Suitable extinguishing agents: Use fire fighting measures that suit the environment.\n· Special hazards arising from the substance or mixture No further relevant information available.\n(Contd. on page 3)\n\n\nPage 3\nPage 3/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Resin - Part A\n(Contd. of page 2)\n59.1.0\n· Advice for firefighters\n· Protective equipment: No special measures required.\n6 Accidental release measures\n· Personal precautions, protective equipment and emergency procedures Not required.\n· Environmental precautions:\nDo not allow product to reach sewage system or any water course.\nDo not allow to enter sewers/ surface or ground water.\nInform respective authorities in case of seepage into water course or sewage system.\n· Methods and material for containment and cleaning up:\nAbsorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).\nDispose contaminated material as waste according to section 13.\nEnsure adequate ventilation.\n· Reference to other sections\nSee Section 7 for information on safe handling.\nSee Section 8 for information on personal protection equipment.\nSee Section 13 for disposal information.\n7 Handling and storage\n· Handling:\n· Precautions for safe handling\nEnsure proper ventilation/exhaustion at workplaces.\nPrevent formation of aerosols.\n· Information about protection against explosions and fires: No special measures required.\n· Conditions for safe storage, including any incompatibilities\n· Storage:\n· Requirements to be met by storerooms and receptacles: Unsuitable materials for receptacle: copper\n· Information about storage in one common storage facility: Not required.\n· Further information about storage conditions:\nKeep receptacle tightly sealed.\nStore receptacle in a well ventilated area.\n· Specific end use(s) No further relevant information available.\n8 Exposure controls/personal protection\n· Additional information about design of technical systems: No additional data. See 7.\n· Control parameters\n· Components with limit values that require monitoring at the workplace:\nThe product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.\n· Exposure controls\n· Personal protective equipment:\n· General protective and hygienic measures:\nKeep away from foodstuffs, beverages and feed.\nImmediately remove all soiled and contaminated clothing.\nWash hands before breaks and at the end of work.\nAvoid contact with the eyes and skin.\n· Breathing equipment: Use suitable respiratory protective device when high concentrations are present.\n· Protection of hands:\nDue to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.\nProtective gloves\nThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.\nSelection of the glove material on consideration of the penetration times, rates of diffusion and the degradation\n(Contd. on page 4)\n\n\nPage 4\nPage 4/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Resin - Part A\n(Contd. of page 3)\n59.1.0\n· Material of gloves\nThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer\nto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance\nand has therefore to be checked prior to the application.\n· Eye protection:\nTightly sealed goggles\n9 Physical and chemical properties\n· Information on basic physical and chemical properties\n· General Information\n· Appearance:\nForm:\nLiquid\nColor:\nYellow tint\n· Odor:\nOdorless\n· Odor threshold:\nNot determined.\n· pH-value:\nNot determined.\n· Change in condition\nMelting point/Melting range:\nUndetermined.\nBoiling point/Boiling range:\n266 °C (510.8 °F)\n· Flash point:\n252 °C (485.6 °F)\n· Flammability (solid, gaseous):\nNot applicable.\n· Decomposition temperature:\nNot determined.\n· Ignition temperature:\nProduct is not selfigniting.\n· Danger of explosion:\nProduct does not present an explosion hazard.\n· Explosion limits:\nLower:\nNot determined.\nUpper:\nNot determined.\n· Vapor pressure:\nNot determined.\n· Density:\nNot determined.\n· Relative density\nNot determined.\n· Vapor density\nNot determined.\n· Specific gravity:\n1.01\n· Evaporation rate\nNot determined.\n· Solubility in / Miscibility with\nWater:\nSlightly soluble.\n· Partition coefficient (n-octanol/water): Not determined.\n· Viscosity:\nDynamic at 20 °C (68 °F):\n400-700 mPas\nKinematic:\nNot determined.\n· Solvent content:\nVOC content:\n0.00 %\n· Other information\nNo further relevant information available.\n(Contd. on page 5)\n\n\nPage 5\nPage 5/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Resin - Part A\n(Contd. of page 4)\n59.1.0\n10 Stability and reactivity\n· Reactivity No further relevant information available.\n· Chemical stability\n· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.\n· Possibility of hazardous reactions No dangerous reactions known.\n· Conditions to avoid\nKeep away from oxidising agents and acidic substances.\nContact with acrylates, aldehydes, atmospheric moisture, halogenates organic and ketones\n· Incompatible materials: Copper and copper alloys\n· Hazardous decomposition products: Carbon monoxide and carbon dioxide\n· Additional information: Hazardous decomposition products may form during combustion.\n11 Toxicological information\n· Information on toxicological effects\n· Acute toxicity:\n· LD/LC50 values that are relevant for classification:\n25068-38-6 reaction product: bisphenol-A-(epichlorhydrin) epoxy resin (number average molecular weight 700)\nOral\nLD50 30,000 mg/kg (rat)\nDermal LD50 23,000 mg/kg (rabbit)\n· Primary chemical irritant effect:\n· on the skin: Irritant to skin and mucous membranes.\n· on the eye: Irritating effect.\n· Sensitization: Sensitization possible through skin contact.\n· Additional toxicological information:\n· Carcinogenic categories\n· IARC (International Agency for Research on Cancer)\nNone of the ingredients is listed.\n· NTP (National Toxicology Program)\nNone of the ingredients is listed.\n· OSHA-Ca (Occupational Safety & Health Administration)\nNone of the ingredients is listed.\n12 Ecological information\n· Toxicity\n· Aquatic toxicity:\n25068-38-6 reaction product: bisphenol-A-(epichlorhydrin) epoxy resin (number average molecular weight 700)\nEC50 (48 h) 1.8 mg/l (water flea)\nLC50 (96 h) 2 mg/l (rainbow trout)\nErC50(72h) 11 mg/l (fresh water algae)\nIC50(18h)\n42.6 mg/l (bacteria)\n· Persistence and degradability No further relevant information available.\n· Behavior in environmental systems:\n· Bioaccumulative potential No further relevant information available.\n· Mobility in soil No further relevant information available.\n· Ecotoxical effects:\n· Remark: Toxic for fish\n· Additional ecological information:\n· General notes:\nWater hazard class 2 (Self-assessment): hazardous for water\nDo not allow product to reach ground water, water course or sewage system.\n(Contd. on page 6)\n\n\nPage 6\nPage 6/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Resin - Part A\n(Contd. of page 5)\n59.1.0\nDanger to drinking water if even small quantities leak into the ground.\nAlso poisonous for fish and plankton in water bodies.\nToxic for aquatic organisms\n· Results of PBT and vPvB assessment\n· PBT: Not applicable.\n· vPvB: Not applicable.\n· Other adverse effects No further relevant information available.\n13 Disposal considerations\n· Waste treatment methods\n· Recommendation: Contact waste processors for recycling information.\n· Uncleaned packagings:\n· Recommendation: Disposal must be made according to official regulations.\n14 Transport information\n· UN-Number\n· DOT, IMDG, IATA\nnot regulated\n· UN proper shipping name\n· DOT, ADN, IMDG, IATA\nnot regulated\n· Transport hazard class(es)\n· DOT, ADN, IMDG, IATA\n· Class\nnot regulated\n· Packing group\n· DOT, IMDG, IATA\nnot regulated\n· Environmental hazards:\n· Marine pollutant:\nYes\n· Special precautions for user\nNot applicable.\n· Transport in bulk according to Annex II of MARPOL73/78 and\nthe IBC Code\nNot applicable.\n· UN "Model Regulation":\nnot regulated\n15 Regulatory information\n· Safety, health and environmental regulations/legislation specific for the substance or mixture\nNo further relevant information available.\n· Sara\n· Section 355 (extremely hazardous substances):\nNone of the ingredients is listed.\n· Section 313 (Specific toxic chemical listings):\nNone of the ingredients is listed.\n· TSCA (Toxic Substances Control Act):\nAll components have the value ACTIVE.\n· Hazardous Air Pollutants\nNone of the ingredients is listed.\n· Proposition 65\n· Chemicals known to cause cancer:\nNone of the ingredients is listed.\n(Contd. on page 7)\n\n\nPage 7\nPage 7/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Resin - Part A\n(Contd. of page 6)\n59.1.0\n· Chemicals known to cause reproductive toxicity for females:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for males:\nNone of the ingredients is listed.\n· Chemicals known to cause developmental toxicity:\nNone of the ingredients is listed.\n· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.\n16 Other information\nTo the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties\nand does not establish a contractual legal relationship.\n· Department issuing SDS: Technical Services\n· Contact: Pablo Mendoza\n· Last revision / supersedes version: 06/01/2024 / 3.0\n· Supersedes date: 12/01/2022\n· Abbreviations and acronyms:\nADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by\nRoad)\nIMDG: International Maritime Code for Dangerous Goods\nDOT: US Department of Transportation\nIATA: International Air Transport Association\nEINECS: European Inventory of Existing Commercial Chemical Substances\nELINCS: European List of Notified Chemical Substances\nCAS: Chemical Abstracts Service (division of the American Chemical Society)\nVOC: Volatile Organic Compounds (USA, EU)\nLC50: Lethal concentration, 50 percent\nLD50: Lethal dose, 50 percent\nPBT: Persistent, Bioaccumulative and Toxic\nvPvB: very Persistent and very Bioaccumulative\nOSHA: Occupational Safety & Health\nTLV: Threshold Limit Value\nPEL: Permissible Exposure Limit\nREL: Recommended Exposure Limit\nSkin Irritation 2: Skin corrosion/irritation – Category 2\nEye Irritation 2A: Serious eye damage/eye irritation – Category 2A\nSensitization - Skin 1: Skin sensitisation – Category 1\nAquatic Chronic 2: Hazardous to the aquatic environment - long-term aquatic hazard – Category 2\n· * Data compared to the previous version altered. \n\n\nPage 8\n \nPage 1/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\n59.1.0\n* 1 Identification\n· Product name: EpoxyMount Hardener - Part B\n· Part number:\n145-10005, 145-10020\n145-10015, 145-10030\n· Application of the substance / the mixture Epoxy curing agent\n· Details of the supplier of the safety data sheet\n· Manufacturer/Supplier:\nAllied High Tech Products Inc.\n16207 Carmenita Road\nUSA-Cerritos, CA, 90703\nUSA\ninfo@alliedhightech.com\n· Information department: Product safety department\n· Emergency telephone number:\nDuring normal opening times: +1 (310) 635-2466\nChemtrec: +1 (202) 483-7616\n2 Hazard(s) identification\n· Classification of the substance or mixture\nGHS05 Corrosion\nSkin Corrosion 1B\nH314 Causes severe skin burns and eye damage.\nEye Damage 1\nH318 Causes serious eye damage.\nGHS07\nSensitization - Skin 1 H317 May cause an allergic skin reaction.\nAquatic Chronic 3\nH412 Harmful to aquatic life with long lasting effects.\n· Label elements\n· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).\n· Hazard pictograms\nGHS05\nGHS07\n· Signal word Danger\n(Contd. on page 2)\n\n\nPage 9\nPage 2/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 1)\n59.1.0\n· Hazard-determining components of labeling:\n2-piperazin-1-ylethylamine\n3-aminomethyl-3,5,5-trimethylcyclohexylamine\ntriethylenetetramine\n· Hazard statements\nCauses severe skin burns and eye damage.\nMay cause an allergic skin reaction.\nHarmful to aquatic life with long lasting effects.\n· Precautionary statements\nDo not breathe dusts or mists.\nWash thoroughly after handling.\nContaminated work clothing must not be allowed out of the workplace.\nAvoid release to the environment.\nWear protective gloves/protective clothing/eye protection/face protection.\nIf swallowed: Rinse mouth. Do NOT induce vomiting.\nIf on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.\nIF INHALED: Remove person to fresh air and keep comfortable for breathing.\nIf in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.\nImmediately call a poison center/doctor.\nSpecific treatment (see on this label).\nIf skin irritation or rash occurs: Get medical advice/attention.\nWash contaminated clothing before reuse.\nStore locked up.\nDispose of contents/container in accordance with local/regional/national/international regulations.\n3 Composition/information on ingredients\n· Chemical characterization: Mixtures\n· Description: Mixture of the substances listed below with nonhazardous additions.\n· Hazardous components and components with occupational exposure limits:\n100-51-6 Benzyl alcohol\n Acute Toxicity - Oral 4, H302; Acute Toxicity - Dermal 4, H312; Acute Toxicity - Inhalation 4, H332\n20-30%\n140-31-8 2-piperazin-1-ylethylamine\n Skin Corrosion 1B, H314; Eye Damage 1, H318;\n Acute Toxicity - Oral 4, H302; Acute Toxicity - Dermal 4,\nH312; Sensitization - Skin 1, H317; Flammable Liquids 4, H227; Aquatic Chronic 3, H412\n20-<25%\n112-24-3 triethylenetetramine\n Skin Corrosion 1B, H314;\n Acute Toxicity - Dermal 4, H312; Sensitization - Skin 1, H317; Aquatic Chronic 3,\nH412\n5-10%\n2855-13-2 3-aminomethyl-3,5,5-trimethylcyclohexylamine\n Skin Corrosion 1B, H314; Eye Damage 1, H318;\n Acute Toxicity - Oral 4, H302; Sensitization - Skin 1A,\nH317\n5-10%\n· Non-hazardous components:\nProprietary Ingredient\n40-50%\n· Additional information: The specific chemical identity and/or exact percentage of the composition has been withheld as a trade secret.\n4 First-aid measures\n· Description of first aid measures\n· General information: Immediately remove any clothing soiled by the product.\n· After inhalation:\nSupply fresh air and to be sure call for a doctor.\nIn case of unconsciousness place patient stably in side position for transportation.\n· After skin contact: Immediately wash with water and soap and rinse thoroughly.\n· After eye contact: Rinse opened eye for several minutes under running water. Then consult a doctor.\n· After swallowing: Drink copious amounts of water and provide fresh air. Immediately call a doctor.\n(Contd. on page 3)\n\n\nPage 10\nPage 3/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 2)\n59.1.0\n· Information for doctor:\n· Most important symptoms and effects, both acute and delayed\nAllergic reactions\nDermatitis\nEye irritation\n· Indication of any immediate medical attention and special treatment needed No further relevant information available.\n5 Fire-fighting measures\n· Extinguishing media\n· Suitable extinguishing agents: Use fire fighting measures that suit the environment.\n· Special hazards arising from the substance or mixture During heating or in case of fire poisonous gases are produced.\n· Advice for firefighters\n· Protective equipment: Wear fully protective suit.\n6 Accidental release measures\n· Personal precautions, protective equipment and emergency procedures\nWear protective equipment. Keep unprotected persons away.\nKeep away from ignition sources\n· Environmental precautions:\nDo not allow product to reach sewage system or any water course.\nDo not allow to enter sewers/ surface or ground water.\nInform respective authorities in case of seepage into water course or sewage system.\n· Methods and material for containment and cleaning up:\nAbsorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).\nUse neutralizing agent.\nDispose contaminated material as waste according to section 13.\nEnsure adequate ventilation.\n· Reference to other sections\nSee Section 7 for information on safe handling.\nSee Section 8 for information on personal protection equipment.\nSee Section 13 for disposal information.\n7 Handling and storage\n· Handling:\n· Precautions for safe handling\nEnsure proper ventilation/exhaustion at workplaces.\nPrevent formation of aerosols.\n· Information about protection against explosions and fires: No special measures required.\n· Conditions for safe storage, including any incompatibilities\n· Storage:\n· Requirements to be met by storerooms and receptacles: Unsuitable materials for receptacle: copper\n· Information about storage in one common storage facility: Not required.\n· Further information about storage conditions:\nProtect from extreme temperatures.\nKeep receptacle tightly sealed.\nStore receptacle in a well ventilated area.\n· Specific end use(s) No further relevant information available.\n8 Exposure controls/personal protection\n· Additional information about design of technical systems: No additional data. See 7.\n· Control parameters\n· Components with limit values that require monitoring at the workplace:\nThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.\nAt this time, the other constituents have no known exposure limits.\n(Contd. on page 4)\n\n\nPage 11\nPage 4/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 3)\n59.1.0\n100-51-6 Benzyl alcohol\nWEEL Long-term value: 10 ppm\n112-24-3 triethylenetetramine\nWEEL Long-term value: 6 mg/m³, 1 ppm\nSkin\n· Exposure controls\n· Personal protective equipment:\n· General protective and hygienic measures:\nKeep away from foodstuffs, beverages and feed.\nImmediately remove all soiled and contaminated clothing.\nWash hands before breaks and at the end of work.\nAvoid contact with the eyes.\nAvoid contact with the eyes and skin.\n· Breathing equipment: Use suitable respiratory protective device when high concentrations are present.\n· Protection of hands:\nDue to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.\nProtective gloves\nThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.\nSelection of the glove material on consideration of the penetration times, rates of diffusion and the degradation\n· Material of gloves\nThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer\nto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance\nand has therefore to be checked prior to the application.\n· Eye protection:\nTightly sealed goggles\n9 Physical and chemical properties\n· Information on basic physical and chemical properties\n· General Information\n· Appearance:\nForm:\nLiquid\nColor:\nYellow tint\n· Odor:\nAmmonia-like\n· Odor threshold:\nNot determined.\n· pH-value at 20 °C (68 °F):\n10-12\n· Change in condition\nMelting point/Melting range:\nUndetermined.\nBoiling point/Boiling range:\n205.4 °C (401.7 °F)\n· Flash point:\nNot applicable.\n· Flammability (solid, gaseous):\nNot applicable.\n· Decomposition temperature:\nNot determined.\n· Ignition temperature:\nProduct is not selfigniting.\n· Danger of explosion:\nProduct does not present an explosion hazard.\n(Contd. on page 5)\n\n\nPage 12\nPage 5/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 4)\n59.1.0\n· Explosion limits:\nLower:\nNot determined.\nUpper:\nNot determined.\n· Vapor pressure:\nNot determined.\n· Density:\nNot determined.\n· Relative density\nNot determined.\n· Vapor density\nNot determined.\n· Specific gravity:\n1.1\n· Evaporation rate\nNot determined.\n· Solubility in / Miscibility with\nWater:\nSlightly soluble.\n· Partition coefficient (n-octanol/water): Not determined.\n· Viscosity:\nDynamic at 20 °C (68 °F):\n500-900 mPas\nKinematic:\nNot determined.\n· Solvent content:\nOrganic solvents:\n20.8 %\nVOC content:\n20.83 %\nSolids content:\n0.0 %\n· Other information\nNo further relevant information available.\n10 Stability and reactivity\n· Reactivity No further relevant information available.\n· Chemical stability\n· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.\n· Possibility of hazardous reactions No dangerous reactions known.\n· Conditions to avoid\nKeep away from oxidising agents and acidic substances.\nContact with acrylates, aldehydes, atmospheric moisture, halogenates organic and ketones\n· Incompatible materials: Copper and copper alloys\n· Hazardous decomposition products: Carbon monoxide and carbon dioxide\n· Additional information: Hazardous decomposition products may form during combustion.\n11 Toxicological information\n· Information on toxicological effects\n· Acute toxicity:\n· LD/LC50 values that are relevant for classification:\nATE (Acute Toxicity Estimate)\nOral\nLD50\n2,877 mg/kg\nDermal\nLD50\n2,251 mg/kg (rabbit)\nInhalative LC50/4 h 52.8 mg/l\n 100-51-6 Benzyl alcohol\nOral\nLD50\n1,230 mg/kg (rat)\nDermal\nLD50\n2,000 mg/kg (rabbit)\nInhalative LC50/4 h 11 mg/l (ATE)\n140-31-8 2-piperazin-1-ylethylamine\nOral\nLD50\n2,140 mg/kg (rat)\n(Contd. on page 6)\n\n\nPage 13\nPage 6/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 5)\n59.1.0\nDermal\nLD50\n880 mg/kg (rabbit)\n112-24-3 triethylenetetramine\nOral\nLD50\n2,500 mg/kg (rat)\nDermal\nLD50\n805 mg/kg (rabbit)\n2855-13-2 3-aminomethyl-3,5,5-trimethylcyclohexylamine\nOral\nLD50\n1,030 mg/kg (ATE)\n· Primary chemical irritant effect:\n· on the skin: Caustic effect on skin and mucous membranes.\n· on the eye:\nStrong caustic effect.\nStrong irritant with the danger of severe eye injury.\n· Sensitization: Sensitization possible through skin contact.\n· Additional toxicological information:\nSwallowing will lead to a strong caustic effect on mouth and throat and to the danger of perforation of esophagus and stomach.\n· Carcinogenic categories\n· IARC (International Agency for Research on Cancer)\nNone of the ingredients is listed.\n· NTP (National Toxicology Program)\nNone of the ingredients is listed.\n· OSHA-Ca (Occupational Safety & Health Administration)\nNone of the ingredients is listed.\n12 Ecological information\n· Toxicity\n· Aquatic toxicity: No further relevant information available.\n· Persistence and degradability No further relevant information available.\n· Behavior in environmental systems:\n· Bioaccumulative potential No further relevant information available.\n· Mobility in soil No further relevant information available.\n· Ecotoxical effects:\n· Remark: Harmful to fish\n· Additional ecological information:\n· General notes:\nWater hazard class 2 (Self-assessment): hazardous for water\nDo not allow product to reach ground water, water course or sewage system.\nMust not reach bodies of water or drainage ditch undiluted or unneutralized.\nDanger to drinking water if even small quantities leak into the ground.\nHarmful to aquatic organisms\nRinse off of bigger amounts into drains or the aquatic environment may lead to increased pH-values. A high pH-value harms aquatic\norganisms. In the dilution of the use-level the pH-value is considerably reduced, so that after the use of the product the aqueous waste,\nemptied into drains, is only low water-dangerous.\n· Results of PBT and vPvB assessment\n· PBT: Not applicable.\n· vPvB: Not applicable.\n· Other adverse effects No further relevant information available.\n13 Disposal considerations\n· Waste treatment methods\n· Recommendation: Contact waste processors for recycling information.\n(Contd. on page 7)\n\n\nPage 14\nPage 7/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 6)\n59.1.0\n· Uncleaned packagings:\n· Recommendation: Disposal must be made according to official regulations.\n14 Transport information\n· UN-Number\n· DOT, IMDG, IATA\nUN2815\n· UN proper shipping name\n· DOT\nN-Aminoethylpiperazine solution\n· IMDG, IATA\nN-AMINOETHYLPIPERAZINE solution\n· Transport hazard class(es)\n· DOT\n· Class\n8 Corrosive substances\n· Label\n8, 6.1\n· IMDG\n· Class\n8 Corrosive substances\n· Label\n8/6.1\n· IATA\n· Class\n8 Corrosive substances\n· Label\n8 (6.1)\n· Packing group\n· DOT, IMDG, IATA\nIII\n· Environmental hazards:\n· Marine pollutant:\nNo\n· Special precautions for user\nWarning: Corrosive substances\n· Hazard identification number (Kemler code):\n86\n· EMS Number:\nF-A,S-B\n· Stowage Category\nB \n· Stowage Code\nSW2 Clear of living quarters.\n· Transport in bulk according to Annex II of MARPOL73/78 and\nthe IBC Code\nNot applicable.\n· Transport/Additional information:\n· DOT\n· Quantity limitations\nOn cargo aircraft only: 60 L\nOn passenger aircraft/rail: 5 L\n· Limited quantities (LQ)\n5L\n· Transport category\n3 \n(Contd. on page 8)\n\n\nPage 15\nPage 8/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 7)\n59.1.0\n· Tunnel restriction code\nE \n· IMDG\n· Limited quantities (LQ)\n5L\n· Excepted quantities (EQ)\nCode: E1\nMaximum net quantity per inner packaging: 30 ml\nMaximum net quantity per outer packaging: 1000 ml\n· UN "Model Regulation":\nUN 2815 N-AMINOETHYLPIPERAZINE SOLUTION, 8 (6.1), III\n15 Regulatory information\n· Safety, health and environmental regulations/legislation specific for the substance or mixture\nNo further relevant information available.\n· Sara\n· Section 355 (extremely hazardous substances):\nNone of the ingredients is listed.\n· Section 313 (Specific toxic chemical listings):\nNone of the ingredients is listed.\n· TSCA (Toxic Substances Control Act):\nAll components have the value ACTIVE.\n· Hazardous Air Pollutants\nNone of the ingredients is listed.\n· Proposition 65\n· Chemicals known to cause cancer:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for females:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for males:\nNone of the ingredients is listed.\n· Chemicals known to cause developmental toxicity:\nNone of the ingredients is listed.\n· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.\n16 Other information\nTo the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties\nand does not establish a contractual legal relationship.\n· Department issuing SDS: Technical Services\n· Contact: Pablo Mendoza\n· Last revision / supersedes version: 06/01/2024 / 3.0\n· Supersedes date: 12/01/2022\n· Abbreviations and acronyms:\nADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by\nRoad)\nIMDG: International Maritime Code for Dangerous Goods\nDOT: US Department of Transportation\nIATA: International Air Transport Association\nEINECS: European Inventory of Existing Commercial Chemical Substances\nELINCS: European List of Notified Chemical Substances\nCAS: Chemical Abstracts Service (division of the American Chemical Society)\nVOC: Volatile Organic Compounds (USA, EU)\nLC50: Lethal concentration, 50 percent\nLD50: Lethal dose, 50 percent\nPBT: Persistent, Bioaccumulative and Toxic\nvPvB: very Persistent and very Bioaccumulative\nOSHA: Occupational Safety & Health\n(Contd. on page 9)\n\n\nPage 16\nPage 9/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: EpoxyMount Hardener - Part B\n(Contd. of page 8)\n59.1.0\nTLV: Threshold Limit Value\nPEL: Permissible Exposure Limit\nREL: Recommended Exposure Limit\nFlammable Liquids 4: Flammable liquids – Category 4\nAcute Toxicity - Oral 4: Acute toxicity – Category 4\nSkin Corrosion 1B: Skin corrosion/irritation – Category 1B\nEye Damage 1: Serious eye damage/eye irritation – Category 1\nSensitization - Skin 1: Skin sensitisation – Category 1\nSensitization - Skin 1A: Skin sensitisation – Category 1A\nAquatic Chronic 3: Hazardous to the aquatic environment - long-term aquatic hazard – Category 3\n· * Data compared to the previous version altered. \n