HOT RELEASE SPRAY: SAFETY DATA SHEET
Also listed as: Mold Release Spray (Hot Mounting)
Refer to the original PDF for tables, figures and page layout.
Page 1\n \nPage 1/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\n59.1.0\n* 1 Identification\n· Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n· Part number: 200-10004\n· Details of the supplier of the safety data sheet\n· Manufacturer/Supplier:\nAllied High Tech Products Inc.\n16207 Carmenita Road\nUSA-Cerritos, CA, 90703\nUSA\ninfo@alliedhightech.com\n· Information department: Product safety department\n· Emergency telephone number:\nDuring normal opening times: +1 (310) 635-2466\nChemtrec: +1 (202) 483-7616\n2 Hazard(s) identification\n· Classification of the substance or mixture\nGHS02 Flame\nFlammable Aerosols 2\nH223\nFlammable aerosol.\nGHS04 Gas cylinder\nGases under Pressure - Compressed gas\nH280\nContains gas under pressure; may explode if heated.\nGHS08 Health hazard\nToxic to Reproduction 1B\nH360\nMay damage fertility or the unborn child.\nSpecific Target Organ Toxicity - Repeated Exposure 2 H373\nMay cause damage to organs through prolonged or repeated exposure.\nGHS07\nAcute Toxicity - Dermal 4\nH312\nHarmful in contact with skin.\nSkin Irritation 2\nH315\nCauses skin irritation.\nEye Irritation 2A\nH319\nCauses serious eye irritation.\nSpecific Target Organ Toxicity - Single Exposure 3\nH335-H336 May cause respiratory irritation. May cause drowsiness or dizziness.\n· Label elements\n· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).\n(Contd. on page 2)\n\n\nPage 2\nPage 2/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 1)\n59.1.0\n· Hazard pictograms\nGHS02\nGHS04\nGHS07\nGHS08\n· Signal word Danger\n· Hazard-determining components of labeling:\n1-bromopropane\nDistillates (petroleum), hydrotreated light\n· Hazard statements\nFlammable aerosol.\nContains gas under pressure; may explode if heated.\nHarmful in contact with skin.\nCauses skin irritation.\nCauses serious eye irritation.\nMay damage fertility or the unborn child.\nMay cause respiratory irritation. May cause drowsiness or dizziness.\nMay cause damage to organs through prolonged or repeated exposure.\n· Precautionary statements\nObtain special instructions before use.\nDo not handle until all safety precautions have been read and understood.\nKeep away from heat/sparks/open flames/hot surfaces. - No smoking.\nDo not spray on an open flame or other ignition source.\nPressurized container: Do not pierce or burn, even after use.\nDo not breathe dust/fume/gas/mist/vapors/spray.\nWash contaminated body parts thoroughly after handling.\nUse only outdoors or in a well-ventilated area.\nWear eye protection / face protection.\nUse personal protective equipment as required.\nIf on skin: Wash with plenty of soap and water.\nIF INHALED: Remove person to fresh air and keep comfortable for breathing.\nIf in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.\nIF exposed or concerned: Get medical advice/attention.\nCall a poison center/doctor if you feel unwell.\nIf skin irritation occurs: Get medical advice/attention.\nTake off contaminated clothing and wash it before reuse.\nIf eye irritation persists: Get medical advice/attention.\nStore in a well-ventilated place. Keep container tightly closed.\nStore locked up.\nProtect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.\nDispose of contents/container in accordance with local/regional/national/international regulations.\n3 Composition/information on ingredients\n· Chemical characterization: Mixtures\n· Description: Mixture of the substances listed below with nonhazardous additions.\n· Hazardous components and components with occupational exposure limits:\n106-94-5 1-bromopropane\n Flammable Liquids 2, H225;\n Carcinogenicity 2, H351; Toxic to Reproduction 1B, H360; Specific Target\nOrgan Toxicity - Repeated Exposure 2, H373;\n Skin Irritation 2, H315; Eye Irritation 2A, H319; Specific Target\nOrgan Toxicity - Single Exposure 3, H335-H336\n75-85%\n68476-86-8 Petroleum gases, liquefied, sweetened\n Flammable Gases 1, H220;\n Gases under Pressure - Compressed gas, H280;\n Germ Cell Mutagenicity 1B,\nH340; Carcinogenicity 1A, H350\n8-15%\n(Contd. on page 3)\n\n\nPage 3\nPage 3/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 2)\n59.1.0\n64742-47-8 Distillates (petroleum), hydrotreated light\n Flammable Liquids 3, H226;\n Aspiration Hazard 1, H304;\n Specific Target Organ Toxicity - Single\nExposure 3, H336\n1-5%\n· Non-hazardous components:\nProprietary Ingredient\n1-5%\n4 First-aid measures\n· Description of first aid measures\n· General information:\nImmediately remove any clothing soiled by the product.\nSymptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.\n· After inhalation: In case of unconsciousness place patient stably in side position for transportation.\n· After skin contact: Immediately wash with water and soap and rinse thoroughly.\n· After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.\n· After swallowing: If symptoms persist consult doctor.\n· Information for doctor:\n· Most important symptoms and effects, both acute and delayed\nHeadache\nDizziness\nNausea\nDermatitis\nEye irritation\n· Indication of any immediate medical attention and special treatment needed No further relevant information available.\n5 Fire-fighting measures\n· Extinguishing media\n· Suitable extinguishing agents: Use fire fighting measures that suit the environment.\n· Special hazards arising from the substance or mixture During heating or in case of fire poisonous gases are produced.\n· Advice for firefighters\n· Protective equipment: Wear fully protective suit.\n6 Accidental release measures\n· Personal precautions, protective equipment and emergency procedures\nWear protective equipment. Keep unprotected persons away.\nEnsure adequate ventilation\nKeep away from ignition sources\n· Environmental precautions: No special measures required.\n· Methods and material for containment and cleaning up:\nDispose contaminated material as waste according to section 13.\nEnsure adequate ventilation.\n· Reference to other sections\nSee Section 7 for information on safe handling.\nSee Section 8 for information on personal protection equipment.\nSee Section 13 for disposal information.\n7 Handling and storage\n· Handling:\n· Precautions for safe handling\nProtect from heat and direct sunlight.\nEnsure proper ventilation/exhaustion at workplaces.\nOpen and handle receptacle with care.\n· Information about protection against explosions and fires:\nKeep ignition sources away - Do not smoke.\nKeep respiratory protective device available.\n(Contd. on page 4)\n\n\nPage 4\nPage 4/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 3)\n59.1.0\n· Conditions for safe storage, including any incompatibilities\n· Storage:\n· Requirements to be met by storerooms and receptacles: Observe official regulations on storing packagings with pressurized containers.\n· Information about storage in one common storage facility: Not required.\n· Further information about storage conditions:\nKeep receptacle tightly sealed.\nStore receptacle in a well ventilated area.\n· Specific end use(s) No further relevant information available.\n8 Exposure controls/personal protection\n· Additional information about design of technical systems: No additional data. See 7.\n· Control parameters\n· Components with limit values that require monitoring at the workplace:\nThe following constituent is the only constituent of the product which has a PEL, TLV or other recommended exposure limit.\nAt this time, the other constituents have no known exposure limits.\n106-94-5 1-bromopropane\nTLV Long-term value: 0.1 ppm\nA3\n· Exposure controls\n· Personal protective equipment:\n· General protective and hygienic measures:\nKeep away from foodstuffs, beverages and feed.\nImmediately remove all soiled and contaminated clothing.\nWash hands before breaks and at the end of work.\nStore protective clothing separately.\nAvoid contact with the eyes and skin.\n· Breathing equipment: Use suitable respiratory protective device when high concentrations are present.\n· Protection of hands:\nProtective gloves\nThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.\nSelection of the glove material on consideration of the penetration times, rates of diffusion and the degradation\n· Material of gloves\nThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer\nto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance\nand has therefore to be checked prior to the application.\n· Eye protection:\nSafety glasses\nTightly sealed goggles\n9 Physical and chemical properties\n· Information on basic physical and chemical properties\n· General Information\n· Appearance:\nForm:\nAerosol\nColor:\nWhite\n· Odor:\nMild\n(Contd. on page 5)\n\n\nPage 5\nPage 5/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 4)\n59.1.0\n· Odor threshold:\nNot determined.\n· pH-value:\nNot determined.\n· Change in condition\nMelting point/Melting range:\n<-45 °C (<-49 °F)\nBoiling point/Boiling range:\n39-87 °C (102.2-188.6 °F)\n· Flash point:\nNot applicable, as aerosol.\n· Flammability (solid, gaseous):\nNot applicable.\n· Auto igniting:\n490 °C (914 °F)\n· Decomposition temperature:\nNot determined.\n· Ignition temperature:\nProduct is not selfigniting.\n· Danger of explosion:\nNot determined.\n· Explosion limits:\nLower:\nNot determined.\nUpper:\nNot determined.\n· Vapor pressure at 20 °C (68 °F):\n78.7 hPa (59 mm Hg)\n· Vapor pressure at 50 °C (122 °F):\n500 hPa (375 mm Hg)\n· Density:\nNot determined.\n· Bulk density:\n1 kg/m³\n· Relative density\nNot determined.\n· Vapor density\nNot determined.\n· Evaporation rate\nNot applicable.\n· Solubility in / Miscibility with\nWater:\nNot miscible or difficult to mix.\n· Partition coefficient (n-octanol/water): Not determined.\n· Viscosity:\nDynamic:\nNot determined.\nKinematic:\nNot determined.\n· Solvent content:\nVOC content:\n0.91-4.55 %\nSolids content:\n0.0 %\n· Other information\nNo further relevant information available.\n10 Stability and reactivity\n· Reactivity No further relevant information available.\n· Chemical stability\n· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.\n· Possibility of hazardous reactions No dangerous reactions known.\n· Conditions to avoid No further relevant information available.\n· Incompatible materials: No further relevant information available.\n· Hazardous decomposition products: No dangerous decomposition products known.\n(Contd. on page 6)\n\n\nPage 6\nPage 6/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 5)\n59.1.0\n11 Toxicological information\n· Information on toxicological effects\n· Acute toxicity:\n· LD/LC50 values that are relevant for classification:\n106-94-5 1-bromopropane\nInhalative LC50/4 h 253 mg/l (rat)\n64742-47-8 Distillates (petroleum), hydrotreated light\nDermal\nLD50\n3,160 mg/kg (rabbit)\n· Primary chemical irritant effect:\n· on the skin: Irritant to skin and mucous membranes.\n· on the eye: Irritating effect.\n· Sensitization: No sensitizing effects known.\n· Additional toxicological information:\nSpecific Target Organ Toxicity - Single Exposure 3 - Target Organ: central nervous system depression\n· Carcinogenic categories\n· IARC (International Agency for Research on Cancer)\n106-94-5 1-bromopropane\n2B\n· NTP (National Toxicology Program)\n106-94-5 1-bromopropane\nR \n· OSHA-Ca (Occupational Safety & Health Administration)\nNone of the ingredients is listed.\n12 Ecological information\n· Toxicity\n· Aquatic toxicity: No further relevant information available.\n· Persistence and degradability No further relevant information available.\n· Behavior in environmental systems:\n· Bioaccumulative potential No further relevant information available.\n· Mobility in soil No further relevant information available.\n· Additional ecological information:\n· General notes:\nDo not allow product to reach ground water, water course or sewage system, even in small quantities.\nDanger to drinking water if even extremely small quantities leak into the ground.\n· Results of PBT and vPvB assessment\n· PBT: Not applicable.\n· vPvB: Not applicable.\n· Other adverse effects No further relevant information available.\n13 Disposal considerations\n· Waste treatment methods\n· Recommendation: Contact waste processors for recycling information.\n· Uncleaned packagings:\n· Recommendation: Disposal must be made according to official regulations.\n14 Transport information\n· UN-Number\n· DOT, IMDG, IATA\nUN1950\n· UN proper shipping name\n· DOT\nAerosols, flammable\n(Contd. on page 7)\n\n\nPage 7\nPage 7/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 6)\n59.1.0\n· IMDG\nAEROSOLS\n· IATA\nAEROSOLS, flammable\n· Transport hazard class(es)\n· DOT\n· Class\n2.1 Gases\n· Label\n2.1\n· IMDG, IATA\n· Class\n2.1 Gases\n· Label\n2.1\n· Packing group\n· DOT, IMDG, IATA\nnot regulated\n· Environmental hazards:\nNot applicable.\n· Special precautions for user\nWarning: Gases\n· Hazard identification number (Kemler code):\n- \n· EMS Number:\nF-D,S-U\n· Stowage Code\nSW1 Protected from sources of heat.\nSW22 For AEROSOLS with a maximum capacity of 1 litre: Category\nA. For AEROSOLS with a capacity above 1 litre: Category B. For\nWASTE AEROSOLS: Category C, Clear of living quarters.\n· Segregation Code\nSG69 For AEROSOLS with a maximum capacity of 1 litre:\nSegregation as for class 9. Stow "separated from" class 1 except for\ndivision 1.4.\nFor AEROSOLS with a capacity above 1 litre:\nSegregation as for the appropriate subdivision of class 2.\nFor WASTE AEROSOLS:\nSegregation as for the appropriate subdivision of class 2.\n· Transport in bulk according to Annex II of MARPOL73/78 and\nthe IBC Code\nNot applicable.\n· Transport/Additional information:\n· DOT\n· Quantity limitations\nOn passenger aircraft/rail: 75 kg\nOn cargo aircraft only: 150 kg\n· Limited quantities (LQ)\n1L\n· Transport category\n2 \n· Tunnel restriction code\nD \n· IMDG\n· Limited quantities (LQ)\n1L\n· Excepted quantities (EQ)\nCode: E0\nNot permitted as Excepted Quantity\n· UN "Model Regulation":\nUN 1950 AEROSOLS, 2.1\n(Contd. on page 8)\n\n\nPage 8\nPage 8/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 7)\n59.1.0\n15 Regulatory information\n· Safety, health and environmental regulations/legislation specific for the substance or mixture\nNo further relevant information available.\n· Sara\n· Section 355 (extremely hazardous substances):\nNone of the ingredients is listed.\n· Section 313 (Specific toxic chemical listings):\n106-94-5 1-bromopropane\n· TSCA (Toxic Substances Control Act):\nAll components have the value ACTIVE.\n· Hazardous Air Pollutants\n106-94-5 1-bromopropane\n· Proposition 65\n· Chemicals known to cause cancer:\n106-94-5 1-bromopropane\n· Chemicals known to cause reproductive toxicity for females:\n106-94-5 1-bromopropane\n· Chemicals known to cause reproductive toxicity for males:\n106-94-5 1-bromopropane\n· Chemicals known to cause developmental toxicity:\n106-94-5 1-bromopropane\n· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.\n16 Other information\nTo the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties\nand does not establish a contractual legal relationship.\n· Department issuing SDS: Technical Services\n· Contact: Pablo Mendoza\n· Last revision / supersedes version: 06/01/2024 / 1.0\n· Supersedes date: 10/10/2023\n· Abbreviations and acronyms:\nADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by\nRoad)\nIMDG: International Maritime Code for Dangerous Goods\nDOT: US Department of Transportation\nIATA: International Air Transport Association\nEINECS: European Inventory of Existing Commercial Chemical Substances\nELINCS: European List of Notified Chemical Substances\nCAS: Chemical Abstracts Service (division of the American Chemical Society)\nVOC: Volatile Organic Compounds (USA, EU)\nLC50: Lethal concentration, 50 percent\nLD50: Lethal dose, 50 percent\nPBT: Persistent, Bioaccumulative and Toxic\nvPvB: very Persistent and very Bioaccumulative\nOSHA: Occupational Safety & Health\nTLV: Threshold Limit Value\nPEL: Permissible Exposure Limit\nREL: Recommended Exposure Limit\nFlammable Gases 1: Flammable gases – Category 1\nFlammable Aerosols 2: Aerosols – Category 2\nGases under Pressure - Compressed gas: Gases under pressure – Compressed gas\nFlammable Liquids 2: Flammable liquids – Category 2\nFlammable Liquids 3: Flammable liquids – Category 3\nAcute Toxicity - Dermal 4: Acute toxicity – Category 4\nSkin Irritation 2: Skin corrosion/irritation – Category 2\nEye Irritation 2A: Serious eye damage/eye irritation – Category 2A\n(Contd. on page 9)\n\n\nPage 9\nPage 9/9\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 2.0\nProduct name: Mold Release Spray, Aerosol Spray (Hot Mouting)\n(Contd. of page 8)\n59.1.0\nGerm Cell Mutagenicity 1B: Germ cell mutagenicity – Category 1B\nCarcinogenicity 1A: Carcinogenicity – Category 1A\nCarcinogenicity 2: Carcinogenicity – Category 2\nToxic to Reproduction 1B: Reproductive toxicity – Category 1B\nSpecific Target Organ Toxicity - Single Exposure 3: Specific target organ toxicity (single exposure) – Category 3\nSpecific Target Organ Toxicity - Repeated Exposure 2: Specific target organ toxicity (repeated exposure) – Category 2\nAspiration Hazard 1: Aspiration hazard – Category 1\n· * Data compared to the previous version altered. \n