Maxi-Cut High Speed Cutting Fluid - Oil Based
Also listed as: SAFETY DATA SHEET
Refer to the original PDF for tables, figures and page layout.
Page 1\n \nPage 1/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\n59.1.0\n* 1 Identification\n· Product name: Maxi-Cut, Oil-Based Cutting Fluid (Undiluted)\n· Part number: 80-10140, 80-10145\n· Application of the substance / the mixture Lubricant\n· Details of the supplier of the safety data sheet\n· Manufacturer/Supplier:\nAllied High Tech Products Inc.\n16207 Carmenita Road\nUSA-Cerritos, CA, 90703\nUSA\ninfo@alliedhightech.com\n· Information department: Product safety department\n· Emergency telephone number:\nDuring normal opening times: +1 (310) 635-2466\nChemtrec: +1 (202) 483-7616\n2 Hazard(s) identification\n· Classification of the substance or mixture\nGHS07\nEye Irritation 2A H319 Causes serious eye irritation.\n· Label elements\n· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).\n· Hazard pictograms\nGHS07\n· Signal word Warning\n· Hazard statements\nCauses serious eye irritation.\n· Precautionary statements\nWash thoroughly after handling.\nWear eye protection / face protection.\nIf in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.\nIf eye irritation persists: Get medical advice/attention.\n(Contd. on page 2)\n\n\nPage 2\nPage 2/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Maxi-Cut, Oil-Based Cutting Fluid (Undiluted)\n(Contd. of page 1)\n59.1.0\n3 Composition/information on ingredients\n· Chemical characterization: Mixtures\n· Description: Mixture of the substances listed below with nonhazardous additions.\n· Hazardous components and components with occupational exposure limits:\n770-35-4 1-Phenoxypropan-2-ol\n Flammable Liquids 3, H226\n>5-9.9%\n· Non-hazardous components:\n64742-52-5 Distillates (petroleum), hydrotreated heavy naphthenic\n>50-<80%\n68608-26-4 Sodium petroleum sulfonate\n>1-6.9%\nCarboxylic acids, alkali salts\n<2%\n· Additional information: The specific chemical identity and/or exact percentage of the composition has been withheld as a trade secret.\n4 First-aid measures\n· Description of first aid measures\n· After inhalation: Supply fresh air; consult doctor in case of complaints.\n· After skin contact: Generally the product does not irritate the skin.\n· After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.\n· After swallowing: If symptoms persist consult doctor.\n· Information for doctor:\n· Most important symptoms and effects, both acute and delayed Eye irritation\n· Indication of any immediate medical attention and special treatment needed No further relevant information available.\n5 Fire-fighting measures\n· Extinguishing media\n· Suitable extinguishing agents:\nCarbon dioxide\nWater spray\nFire-extinguishing powder\nUse fire fighting measures that suit the environment.\n· Special hazards arising from the substance or mixture No further relevant information available.\n· Advice for firefighters\n· Protective equipment: No special measures required.\n6 Accidental release measures\n· Personal precautions, protective equipment and emergency procedures Not required.\n· Environmental precautions:\nDo not allow product to reach sewage system or any water course.\nDo not allow to enter sewers/ surface or ground water.\nDilute with plenty of water.\n· Methods and material for containment and cleaning up:\nAbsorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).\n· Reference to other sections\nSee Section 7 for information on safe handling.\nSee Section 8 for information on personal protection equipment.\nSee Section 13 for disposal information.\n7 Handling and storage\n· Handling:\n· Precautions for safe handling No special precautions are necessary if used correctly.\n· Information about protection against explosions and fires: No special measures required.\n· Conditions for safe storage, including any incompatibilities\n· Storage:\n· Requirements to be met by storerooms and receptacles: Store only in the original receptacle.\n(Contd. on page 3)\n\n\nPage 3\nPage 3/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Maxi-Cut, Oil-Based Cutting Fluid (Undiluted)\n(Contd. of page 2)\n59.1.0\n· Information about storage in one common storage facility: Store away from oxidizing agents.\n· Further information about storage conditions:\nProtect from frost.\nStorage temperature between -40 °C and 40 °C\nDuration of storage: In closed, original container, at least 24 months\nKeep receptacle tightly sealed.\n· Specific end use(s) No further relevant information available.\n8 Exposure controls/personal protection\n· Additional information about design of technical systems: No additional data. See 7.\n· Control parameters\n· Components with limit values that require monitoring at the workplace:\nThe product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.\n· Exposure controls\n· Personal protective equipment:\n· General protective and hygienic measures:\nKeep away from foodstuffs, beverages and feed.\nImmediately remove all soiled and contaminated clothing.\nWash hands before breaks and at the end of work.\nAvoid contact with the eyes.\nAvoid contact with the eyes and skin.\n· Breathing equipment:\nNot required.\nUse suitable respiratory protective device in case of insufficient ventilation.\n· Protection of hands:\nProtective gloves\nThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.\nSelection of the glove material on consideration of the penetration times, rates of diffusion and the degradation\n· Material of gloves\nNitrile rubber, NBR\nRecommended thickness of the material: 0.3 mm\nThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer\nto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance\nand has therefore to be checked prior to the application.\n· Eye protection:\nTightly sealed goggles\n9 Physical and chemical properties\n· Information on basic physical and chemical properties\n· General Information\n· Appearance:\nForm:\nLiquid\nColor:\nLight brown\n· Odor:\nAlmonds\n· Odor threshold:\nNot determined.\n· pH-value at 20 °C (68 °F):\n8.5-9.2 (at 5% in water)\n(Contd. on page 4)\n\n\nPage 4\nPage 4/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Maxi-Cut, Oil-Based Cutting Fluid (Undiluted)\n(Contd. of page 3)\n59.1.0\n· Change in condition\nMelting point/Melting range:\nUndetermined.\nBoiling point/Boiling range:\n300 °C (572 °F)\n· Flash point:\n150 °C (302 °F)\n· Flammability (solid, gaseous):\nNot applicable.\n· Decomposition temperature:\nNot determined.\n· Ignition temperature:\nProduct is not selfigniting.\n· Danger of explosion:\nProduct does not present an explosion hazard.\n· Explosion limits:\nLower:\n0.6 Vol %\nUpper:\n6.5 Vol %\n· Vapor pressure:\nNot determined.\n· Density at 20 °C (68 °F):\n0.98 g/cm³ (8.178 lbs/gal)\n· Relative density\nNot determined.\n· Vapor density\nNot determined.\n· Evaporation rate\nNot determined.\n· Solubility in / Miscibility with\nWater:\nEmulsifiable.\n· Partition coefficient (n-octanol/water): Not determined.\n· Viscosity:\nDynamic:\nNot determined.\nKinematic at 40 °C (104 °F):\n68 mm²/s\n· Solvent content:\nVOC content:\n0.00 %\nSolids content:\n0.0 %\n· Other information\nNo further relevant information available.\n10 Stability and reactivity\n· Reactivity No further relevant information available.\n· Chemical stability\n· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.\n· Possibility of hazardous reactions No dangerous reactions known.\n· Conditions to avoid Keep away from oxidising agents and acidic substances.\n· Incompatible materials: No further relevant information available.\n· Hazardous decomposition products:\nChlorine compounds\nSulfur oxides (SOx)\nNitrogen oxides (NOx)\nCarbon monoxide and carbon dioxide\n· Additional information: Hazardous decomposition products may form during combustion.\n11 Toxicological information\n· Information on toxicological effects\n· Acute toxicity:\n· LD/LC50 values that are relevant for classification:\nOral\nLD50\n7,220 mg/kg (rat)\nInhalative LC50/4 h 65.5 mg/l (rat)\n(Contd. on page 5)\n\n\nPage 5\nPage 5/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Maxi-Cut, Oil-Based Cutting Fluid (Undiluted)\n(Contd. of page 4)\n59.1.0\n· Primary chemical irritant effect:\n· on the skin: No irritant effect.\n· on the eye: Irritating effect.\n· Sensitization: No sensitizing effects known.\n· Additional toxicological information:\n· Carcinogenic categories\n· IARC (International Agency for Research on Cancer)\nNone of the ingredients is listed.\n· NTP (National Toxicology Program)\nNone of the ingredients is listed.\n· OSHA-Ca (Occupational Safety & Health Administration)\nNone of the ingredients is listed.\n12 Ecological information\n· Toxicity\n· Aquatic toxicity: No further relevant information available.\n· Persistence and degradability No further relevant information available.\n· Behavior in environmental systems:\n· Bioaccumulative potential No further relevant information available.\n· Mobility in soil No further relevant information available.\n· Additional ecological information:\n· General notes:\nWater hazard class 1 (Self-assessment): slightly hazardous for water\nDo not allow undiluted product or large quantities of it to reach ground water, water course or sewage system.\n· Results of PBT and vPvB assessment\n· PBT: Not applicable.\n· vPvB: Not applicable.\n· Other adverse effects No further relevant information available.\n13 Disposal considerations\n· Waste treatment methods\n· Recommendation: Contact waste processors for recycling information.\n· Uncleaned packagings:\n· Recommendation: Disposal must be made according to official regulations.\n· Recommended cleansing agent: Water, if necessary with cleansing agents.\n14 Transport information\n· UN-Number\n· DOT, ADN, IMDG, IATA\nnot regulated\n· UN proper shipping name\n· DOT, ADN, IMDG, IATA\nnot regulated\n· Transport hazard class(es)\n· DOT, ADN, IMDG, IATA\n· Class\nnot regulated\n· Packing group\n· DOT, IMDG, IATA\nnot regulated\n· Environmental hazards:\n· Marine pollutant:\nNo\n(Contd. on page 6)\n\n\nPage 6\nPage 6/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Maxi-Cut, Oil-Based Cutting Fluid (Undiluted)\n(Contd. of page 5)\n59.1.0\n· Special precautions for user\nNot applicable.\n· Transport in bulk according to Annex II of MARPOL73/78 and\nthe IBC Code\nNot applicable.\n· UN "Model Regulation":\nnot regulated\n15 Regulatory information\n· Safety, health and environmental regulations/legislation specific for the substance or mixture\nNo further relevant information available.\n· Sara\n· Section 355 (extremely hazardous substances):\nNone of the ingredients is listed.\n· Section 313 (Specific toxic chemical listings):\nNone of the ingredients is listed.\n· TSCA (Toxic Substances Control Act):\n64742-52-5 Distillates (petroleum), hydrotreated heavy naphthenic\nACTIVE\n770-35-4 1-Phenoxypropan-2-ol\nACTIVE\n68608-26-4 Sodium petroleum sulfonate\nACTIVE\n· Hazardous Air Pollutants\nNone of the ingredients is listed.\n· Proposition 65\n· Chemicals known to cause cancer:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for females:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for males:\nNone of the ingredients is listed.\n· Chemicals known to cause developmental toxicity:\nNone of the ingredients is listed.\n· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.\n16 Other information\nTo the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties\nand does not establish a contractual legal relationship.\n· Department issuing SDS: Technical Services\n· Contact: Pablo Mendoza\n· Last revision / supersedes version: 06/01/2024 / 3.0\n· Supersedes date: 12/02/2022\n· Abbreviations and acronyms:\nADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by\nRoad)\nIMDG: International Maritime Code for Dangerous Goods\nDOT: US Department of Transportation\nIATA: International Air Transport Association\nEINECS: European Inventory of Existing Commercial Chemical Substances\nELINCS: European List of Notified Chemical Substances\nCAS: Chemical Abstracts Service (division of the American Chemical Society)\nVOC: Volatile Organic Compounds (USA, EU)\nLC50: Lethal concentration, 50 percent\nLD50: Lethal dose, 50 percent\nPBT: Persistent, Bioaccumulative and Toxic\nvPvB: very Persistent and very Bioaccumulative\nOSHA: Occupational Safety & Health\n(Contd. on page 7)\n\n\nPage 7\nPage 7/7\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 4.0\nProduct name: Maxi-Cut, Oil-Based Cutting Fluid (Undiluted)\n(Contd. of page 6)\n59.1.0\nTLV: Threshold Limit Value\nPEL: Permissible Exposure Limit\nREL: Recommended Exposure Limit\nFlammable Liquids 3: Flammable liquids – Category 3\nEye Irritation 2A: Serious eye damage/eye irritation – Category 2A\n· * Data compared to the previous version altered. \n