PTFE RELEASE SPRAY: SAFETY DATA SHEET
Also listed as: Mold Release Spray, PTFE Based (Hot or Cold)
Refer to the original PDF for tables, figures and page layout.
Page 1\n \nPage 1/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\n59.1.0\n* 1 Identification\n· Product name: Mold Release Spray, PTFE Based\n· Part number: 200-10006\n· Application of the substance / the mixture Releasing agent\n· Details of the supplier of the safety data sheet\n· Manufacturer/Supplier:\nAllied High Tech Products Inc.\n16207 Carmenita Road\nUSA-Cerritos, CA, 90703\nUSA\ninfo@alliedhightech.com\n· Information department: Product safety department\n· Emergency telephone number:\nDuring normal opening times: +1 (310) 635-2466\nChemtrec: +1 (202) 483-7616\n2 Hazard(s) identification\n· Classification of the substance or mixture\nGHS02 Flame\nFlammable Aerosols 1\nH222 Extremely flammable aerosol.\nGHS04 Gas cylinder\nGases under Pressure - Compressed gas\nH280 Contains gas under pressure; may explode if heated.\nGHS08 Health hazard\nToxic to Reproduction 2\nH361 Suspected of damaging fertility or the unborn child.\nAspiration Hazard 1\nH304 May be fatal if swallowed and enters airways.\nGHS09 Environment\nAquatic Chronic 2\nH411 Toxic to aquatic life with long lasting effects.\nGHS07\n(Contd. on page 2)\n\n\nPage 2\nPage 2/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 1)\n59.1.0\nSkin Irritation 2\nH315 Causes skin irritation.\nEye Irritation 2A\nH319 Causes serious eye irritation.\nSpecific Target Organ Toxicity - Single Exposure 3 H336 May cause drowsiness or dizziness.\n· Label elements\n· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).\n· Hazard pictograms\nGHS02\nGHS04\nGHS07\nGHS08\nGHS09\n· Signal word Danger\n· Hazard-determining components of labeling:\n2-methylpentane\nn-hexane\n3-methylpentane\nisopropyl alcohol\n· Hazard statements\nExtremely flammable aerosol.\nContains gas under pressure; may explode if heated.\nCauses skin irritation.\nCauses serious eye irritation.\nSuspected of damaging fertility or the unborn child.\nMay cause drowsiness or dizziness.\nMay be fatal if swallowed and enters airways.\nToxic to aquatic life with long lasting effects.\n· Precautionary statements\nObtain special instructions before use.\nDo not handle until all safety precautions have been read and understood.\nKeep away from heat/sparks/open flames/hot surfaces. - No smoking.\nDo not spray on an open flame or other ignition source.\nPressurized container: Do not pierce or burn, even after use.\nAvoid breathing dust/fume/gas/mist/vapors/spray\nWash thoroughly after handling.\nUse only outdoors or in a well-ventilated area.\nAvoid release to the environment.\nWear protective gloves/protective clothing/eye protection/face protection.\nIf swallowed: Immediately call a poison center/doctor.\nSpecific treatment (see on this label).\nDo NOT induce vomiting.\nIf on skin: Wash with plenty of water.\nIF INHALED: Remove person to fresh air and keep comfortable for breathing.\nIf in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.\nIF exposed or concerned: Get medical advice/attention.\nCall a poison center/doctor if you feel unwell.\nTake off contaminated clothing and wash it before reuse.\nIf skin irritation occurs: Get medical advice/attention.\nIf eye irritation persists: Get medical advice/attention.\nCollect spillage.\nStore in a well-ventilated place. Keep container tightly closed.\nStore locked up.\nProtect from sunlight. Store in a well-ventilated place.\nProtect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.\n(Contd. on page 3)\n\n\nPage 3\nPage 3/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 2)\n59.1.0\nDispose of contents/container in accordance with local/regional/national/international regulations.\n3 Composition/information on ingredients\n· Chemical characterization: Mixtures\n· Description: Mixture of the substances listed below with nonhazardous additions.\n· Hazardous components and components with occupational exposure limits:\n75-37-6 1,1-difluoroethane\n Flammable Liquids 1, H224\n40-50%\n67-63-0 isopropyl alcohol\n Flammable Liquids 2, H225;\n Eye Irritation 2A, H319; Specific Target Organ Toxicity - Single Exposure 3,\nH336\n10-<20%\n107-83-5 2-methylpentane\n Flammable Liquids 2, H225;\n Aspiration Hazard 1, H304;\n Aquatic Chronic 2, H411;\n Skin Irritation 2,\nH315; Specific Target Organ Toxicity - Single Exposure 3, H336\n10-<20%\n96-14-0 3-methylpentane\n Flammable Liquids 2, H225;\n Aspiration Hazard 1, H304;\n Aquatic Chronic 2, H411;\n Skin Irritation 2,\nH315; Specific Target Organ Toxicity - Single Exposure 3, H336\n5-<10%\n75-83-2 2,2-dimethylbutane\n Flammable Liquids 2, H225;\n Aspiration Hazard 1, H304;\n Aquatic Chronic 2, H411;\n Skin Irritation 2,\nH315; Specific Target Organ Toxicity - Single Exposure 3, H336\n2.5-<5%\n79-29-8 2,3-dimethylbutane\n Flammable Liquids 2, H225;\n Aspiration Hazard 1, H304;\n Aquatic Chronic 2, H411;\n Skin Irritation 2,\nH315; Specific Target Organ Toxicity - Single Exposure 3, H336\n2.5-<5%\n110-54-3 n-hexane\n Flammable Liquids 2, H225;\n Toxic to Reproduction 2, H361;\n Acute Toxicity - Inhalation 4, H332\n0.1-≤1%\n· Additional information: The specific chemical identity and/or exact percentage of the composition has been withheld as a trade secret.\n4 First-aid measures\n· Description of first aid measures\n· General information: Immediately remove any clothing soiled by the product.\n· After inhalation: In case of unconsciousness place patient stably in side position for transportation.\n· After skin contact: Immediately wash with water and soap and rinse thoroughly.\n· After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.\n· After swallowing: If symptoms persist consult doctor.\n· Information for doctor:\n· Most important symptoms and effects, both acute and delayed\nRedness\nSwelling\nHeadache\nDizziness\nNausea\nDermatitis\nEye irritation\n· Indication of any immediate medical attention and special treatment needed No further relevant information available.\n5 Fire-fighting measures\n· Extinguishing media\n· Suitable extinguishing agents: Use fire fighting measures that suit the environment.\n· Special hazards arising from the substance or mixture No further relevant information available.\n· Advice for firefighters\n· Protective equipment: Wear fully protective suit.\n(Contd. on page 4)\n\n\nPage 4\nPage 4/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 3)\n59.1.0\n6 Accidental release measures\n· Personal precautions, protective equipment and emergency procedures\nWear protective equipment. Keep unprotected persons away.\nEnsure adequate ventilation\nKeep away from ignition sources\n· Environmental precautions:\nDo not allow to enter sewers/ surface or ground water.\nInform respective authorities in case of seepage into water course or sewage system.\n· Methods and material for containment and cleaning up:\nDispose contaminated material as waste according to section 13.\nEnsure adequate ventilation.\n· Reference to other sections\nSee Section 7 for information on safe handling.\nSee Section 8 for information on personal protection equipment.\nSee Section 13 for disposal information.\n7 Handling and storage\n· Handling:\n· Precautions for safe handling\nProtect from heat and direct sunlight.\nEnsure proper ventilation/exhaustion at workplaces.\nOpen and handle receptacle with care.\n· Information about protection against explosions and fires:\nDo not spray on a naked flame or any incandescent material.\nKeep ignition sources away - Do not smoke.\n· Conditions for safe storage, including any incompatibilities\n· Storage:\n· Requirements to be met by storerooms and receptacles:\nProtect from sunlight.\nStore at temperatures not exceeding 49°C.\nObserve official regulations on storing packagings with pressurized containers.\n· Information about storage in one common storage facility: Not required.\n· Further information about storage conditions:\nKeep receptacle tightly sealed.\nStore receptacle in a well ventilated area.\n· Specific end use(s) No further relevant information available.\n8 Exposure controls/personal protection\n· Additional information about design of technical systems: No additional data. See 7.\n· Control parameters\n· Components with limit values that require monitoring at the workplace:\nThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.\nAt this time, the remaining constituent has no known exposure limits.\n67-63-0 isopropyl alcohol\nPEL Long-term value: 980 mg/m³, 400 ppm\nREL Short-term value: 1225 mg/m³, 500 ppm\nLong-term value: 980 mg/m³, 400 ppm\nTLV Short-term value: 400 ppm\nLong-term value: 200 ppm\nBEI, A4\n(Contd. on page 5)\n\n\nPage 5\nPage 5/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 4)\n59.1.0\n107-83-5 2-methylpentane\nREL Long-term value: 350 mg/m³, 100 ppm\nCeiling limit value: 1800* mg/m³, 510* ppm\n*15-min\nTLV Long-term value: 200 ppm\nA3\n96-14-0 3-methylpentane\nREL Long-term value: 350 mg/m³, 100 ppm\nCeiling limit value: 1800* mg/m³, 510* ppm\n*15-min\nTLV Long-term value: 200 ppm\nA3\n75-83-2 2,2-dimethylbutane\nREL Long-term value: 350 mg/m³, 100 ppm\nCeiling limit value: 1800* mg/m³, 510* ppm\n*15-min\nTLV Long-term value: 200 ppm\nA3\n79-29-8 2,3-dimethylbutane\nREL Long-term value: 350 mg/m³, 100 ppm\nCeiling limit value: 1800* mg/m³, 510* ppm\n*15-min\nTLV Long-term value: 200 ppm\nA3\n110-54-3 n-hexane\nPEL Long-term value: 1800 mg/m³, 500 ppm\nREL Long-term value: 180 mg/m³, 50 ppm\nTLV Long-term value: 50 ppm\nSkin; BEI\n· Ingredients with biological limit values:\n67-63-0 isopropyl alcohol\nBEI 40 mg/L\nMedium: urine\nTime: end of shift at end of workweek\nParameter: Acetone (background, nonspecific)\n110-54-3 n-hexane\nBEI 0.5 mg/L\nMedium: urine\nTime: end of shift\nParameter: 2.5-Hexanedione without hydrolysis\n· Exposure controls\n· Personal protective equipment:\n· General protective and hygienic measures:\nKeep away from foodstuffs, beverages and feed.\nImmediately remove all soiled and contaminated clothing.\nWash hands before breaks and at the end of work.\nStore protective clothing separately.\nAvoid contact with the eyes and skin.\n· Breathing equipment: Use suitable respiratory protective device when high concentrations are present.\n(Contd. on page 6)\n\n\nPage 6\nPage 6/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 5)\n59.1.0\n· Protection of hands:\nDue to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.\nProtective gloves\nThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.\nSelection of the glove material on consideration of the penetration times, rates of diffusion and the degradation\n· Material of gloves\nThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer\nto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance\nand has therefore to be checked prior to the application.\n· Eye protection:\nTightly sealed goggles\n9 Physical and chemical properties\n· Information on basic physical and chemical properties\n· General Information\n· Appearance:\nForm:\nAerosol\nColor:\nWhite\n· Odor:\nAlcohol-like\n· Odor threshold:\nNot determined.\n· pH-value:\nNot determined.\n· Change in condition\nMelting point/Melting range:\nUndetermined.\nBoiling point/Boiling range:\nNot applicable, as aerosol.\n· Flash point:\nNot applicable, as aerosol.\n· Flammability (solid, gaseous):\nNot applicable.\n· Decomposition temperature:\nNot determined.\n· Ignition temperature:\nProduct is not selfigniting.\n· Danger of explosion:\nNot determined.\n· Explosion limits:\nLower:\nNot determined.\nUpper:\nNot determined.\n· Vapor pressure at 20 °C (68 °F):\n5,066 hPa (3.866 mm Hg)\n· Density:\nNot determined.\n· Relative density\nNot determined.\n· Vapor density\n>1 (Air = 1)\n· Specific gravity at 20 °C (68 °F):\n0.82\n· Evaporation rate\n>1 (BuAc = 1)\n· Solubility in / Miscibility with\nWater:\nPartly miscible.\n· Partition coefficient (n-octanol/water): Not determined.\n(Contd. on page 7)\n\n\nPage 7\nPage 7/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 6)\n59.1.0\n· Viscosity:\nDynamic:\nNot determined.\nKinematic:\nNot determined.\n· Solvent content:\nOrganic solvents:\n22.5 %\nVOC content:\n40.54 %\nSolids content:\n0.0 %\n· Other information\nNo further relevant information available.\n10 Stability and reactivity\n· Reactivity No further relevant information available.\n· Chemical stability\n· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.\n· Possibility of hazardous reactions No dangerous reactions known.\n· Conditions to avoid\nKeep away from oxidising agents and acidic substances.\nKeep away from heat.\nKeep away from open flames. - No smoking.\n· Incompatible materials: Chlorine\n· Hazardous decomposition products: Carbon monoxide and carbon dioxide\n· Additional information: Hazardous decomposition products may form during combustion.\n11 Toxicological information\n· Information on toxicological effects\n· Acute toxicity:\n· LD/LC50 values that are relevant for classification:\n75-37-6 1,1-difluoroethane\nInhalative LC50/4 h 977 mg/l (mouse)\n67-63-0 isopropyl alcohol\nOral\nLD50\n5,045 mg/kg (rat)\nDermal\nLD50\n12,800 mg/kg (rabbit)\nInhalative LC50/4 h 30 mg/l (rat)\n110-54-3 n-hexane\nInhalative LC50/4 h 11 mg/l (ATE)\n· Primary chemical irritant effect:\n· on the skin: Irritant to skin and mucous membranes.\n· on the eye: Irritating effect.\n· Sensitization: No sensitizing effects known.\n· Additional toxicological information:\nSpecific Target Organ Toxicity - Single Exposure 3 - Target Organ: central nervous system depression\n· Carcinogenic categories\n· IARC (International Agency for Research on Cancer)\n67-63-0 isopropyl alcohol\n3 \n· NTP (National Toxicology Program)\nNone of the ingredients is listed.\n· OSHA-Ca (Occupational Safety & Health Administration)\nNone of the ingredients is listed.\n(Contd. on page 8)\n\n\nPage 8\nPage 8/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 7)\n59.1.0\n12 Ecological information\n· Toxicity\n· Aquatic toxicity:\nLC50 (96 h) 11,130 mg/l (pimephales promelas)\n 110-54-3 n-hexane\nLC50 (96 h) 2.981 mg/l (pimephales promelas)\n· Persistence and degradability No further relevant information available.\n· Behavior in environmental systems:\n· Bioaccumulative potential May be accumulated in organism\n· Mobility in soil No further relevant information available.\n· Ecotoxical effects:\n· Remark: Toxic for fish\n· Additional ecological information:\n· General notes:\nWater hazard class 2 (Self-assessment): hazardous for water\nDo not allow product to reach ground water, water course or sewage system.\nDanger to drinking water if even small quantities leak into the ground.\nAlso poisonous for fish and plankton in water bodies.\nToxic for aquatic organisms\n· Results of PBT and vPvB assessment\n· PBT: Not applicable.\n· vPvB: Not applicable.\n· Other adverse effects No further relevant information available.\n13 Disposal considerations\n· Waste treatment methods\n· Recommendation: Contact waste processors for recycling information.\n· Uncleaned packagings:\n· Recommendation: Disposal must be made according to official regulations.\n14 Transport information\n· UN-Number\n· DOT, IMDG, IATA\nUN1950\n· UN proper shipping name\n· DOT\nAerosols, flammable\n· IMDG\nAEROSOLS, MARINE POLLUTANT\n· IATA\nAEROSOLS, flammable\n· Transport hazard class(es)\n· DOT\n· Class\n2.1 Gases\n· Label\n2.1\n(Contd. on page 9)\n\n\nPage 9\nPage 9/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 8)\n59.1.0\n· IMDG\n· Class\n2.1 Gases\n· Label\n2.1\n· IATA\n· Class\n2.1 Gases\n· Label\n2.1\n· Packing group\n· DOT, IMDG, IATA\nnot regulated\n· Environmental hazards:\nProduct contains environmentally hazardous substances: 2-\nmethylpentane\n· Marine pollutant:\nNo\nSymbol (fish and tree)\n· Special precautions for user\nWarning: Gases\n· Hazard identification number (Kemler code):\n- \n· EMS Number:\nF-D,S-U\n· Stowage Code\nSW1 Protected from sources of heat.\nSW2 Clear of living quarters.\n· Segregation Code\nSG69 For AEROSOLS with a maximum capacity of 1 litre:\nSegregation as for class 9. Stow "separated from" class 1 except for\ndivision 1.4.\nFor AEROSOLS with a capacity above 1 litre:\nSegregation as for the appropriate subdivision of class 2.\nFor WASTE AEROSOLS:\nSegregation as for the appropriate subdivision of class 2.\n· Transport in bulk according to Annex II of MARPOL73/78 and\nthe IBC Code\nNot applicable.\n· Transport/Additional information:\n· DOT\n· Quantity limitations\nOn passenger aircraft/rail: 75 kg\nOn cargo aircraft only: 150 kg\n· Limited quantities (LQ)\n1L\n· Transport category\n2 \n· Tunnel restriction code\nD \n· IMDG\n· Limited quantities (LQ)\n1L\n· Excepted quantities (EQ)\nCode: E0\nNot permitted as Excepted Quantity\n· UN "Model Regulation":\nUN 1950 AEROSOLS, 2.1, ENVIRONMENTALLY HAZARDOUS\n15 Regulatory information\n· Safety, health and environmental regulations/legislation specific for the substance or mixture\nNo further relevant information available.\n(Contd. on page 10)\n\n\nPage 10\nPage 10/10\nSafety Data Sheet\nacc. to OSHA HCS\nPrinting date 07/02/2024\nLast revision 06/01/2024\nVersion 5.0\nProduct name: Mold Release Spray, PTFE Based\n(Contd. of page 9)\n59.1.0\n· Sara\n· Section 355 (extremely hazardous substances):\nNone of the ingredients is listed.\n· Section 313 (Specific toxic chemical listings):\n67-63-0 isopropyl alcohol\n110-54-3 n-hexane\n· TSCA (Toxic Substances Control Act):\nAll components have the value ACTIVE.\n· Hazardous Air Pollutants\n110-54-3 n-hexane\n· Proposition 65\n· Chemicals known to cause cancer:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for females:\nNone of the ingredients is listed.\n· Chemicals known to cause reproductive toxicity for males:\n110-54-3 n-hexane\n· Chemicals known to cause developmental toxicity:\nNone of the ingredients is listed.\n· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.\n16 Other information\nTo the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties\nand does not establish a contractual legal relationship.\n· Department issuing SDS: Technical Services\n· Contact: Pablo Mendoza\n· Last revision / supersedes version: 06/01/2024 / 4.0\n· Supersedes date: 06/01/2022\n· Abbreviations and acronyms:\nADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by\nRoad)\nIMDG: International Maritime Code for Dangerous Goods\nDOT: US Department of Transportation\nIATA: International Air Transport Association\nEINECS: European Inventory of Existing Commercial Chemical Substances\nELINCS: European List of Notified Chemical Substances\nCAS: Chemical Abstracts Service (division of the American Chemical Society)\nVOC: Volatile Organic Compounds (USA, EU)\nLC50: Lethal concentration, 50 percent\nLD50: Lethal dose, 50 percent\nPBT: Persistent, Bioaccumulative and Toxic\nvPvB: very Persistent and very Bioaccumulative\nOSHA: Occupational Safety & Health\nTLV: Threshold Limit Value\nPEL: Permissible Exposure Limit\nREL: Recommended Exposure Limit\nBEI: Biological Exposure Limit\nFlammable Aerosols 1: Aerosols – Category 1\nGases under Pressure - Compressed gas: Gases under pressure – Compressed gas\nFlammable Liquids 1: Flammable liquids – Category 1\nFlammable Liquids 2: Flammable liquids – Category 2\nAcute Toxicity - Inhalation 4: Acute toxicity – Category 4\nSkin Irritation 2: Skin corrosion/irritation – Category 2\nEye Irritation 2A: Serious eye damage/eye irritation – Category 2A\nToxic to Reproduction 2: Reproductive toxicity – Category 2\nSpecific Target Organ Toxicity - Single Exposure 3: Specific target organ toxicity (single exposure) – Category 3\nAspiration Hazard 1: Aspiration hazard – Category 1\nAquatic Chronic 2: Hazardous to the aquatic environment - long-term aquatic hazard – Category 2\n· * Data compared to the previous version altered. \n