QuickSet Acrylic Use & Mixing Instructions
Also listed as: PRODUCT USE INSTRUCTIONS
Refer to the original PDF for tables, figures and page layout.
Page 1\n \n \nProduct Guide \nwww.alliedhightech.com \nAllied High Tech Products, Inc. \nCall for more information: 800.675.1118 \nQuickSet Acrylic Mounting Resin \nDate: 10/2020, v1.7\nRefer to the SDS document for \nadditional safety information. \n \nQuickSet is a fast-curing acrylic for cold mounting of a variety of metallographic specimens, \nespecially printed circuit boards (PCBs) and other electronic components. It provides good edge \nretention and very low shrinkage. \n \nInstructions \n1. Clean the sample using micro organic soap, isopropyl alcohol and/or an ultrasonic \ncleaner to improve mounting material adhesion and prevent outgassing. Dry with heat \nor clean air to remove all moisture prior to mounting. \n2. Pour two (2) parts powder into a mixing cup and one (1) part liquid into another cup. \nNote: Do not use wax lined or paper cups. Unless they are cooled in water, the use of \ndisposable mounting cups is also not recommended to avoid melting the cup itself. \n3. Pour the powder into the liquid. Stir gently until the mixture appears homogenous. \nNote: If a thinner mixture is desired, more liquid can be added; however, the cure time \nwill increase. \n4. Pour the mixture over the sample in the mounting cup. \n5. Let the mount harden/cure. \n \nEliminating Bubbles & Air Pockets \nA pressure chamber can be used to eliminate bubble formation by filling open pores and \ncavities, which can interfere with adhesion of the mounting resin to the sample and can collect \ndebris during grinding and polishing. Debris will contaminate the polishing cloths, leaving \nscratches on the polished surface. After pouring the acrylic, fully cure the mount in a pressure \nchamber at 25-30 psi. \n \nSample Removal \nWhen cured, QuickSet is non-soluble in alcohol and soluble in acetone. If a sample needs to be \nremoved from acrylic that is cured or not fully cured, it can be dissolved using acetone. \n \n \nTechnical Information \nMixing Ratio (by volume) \n2:1 Powder to Liquid* \nCuring Time \n6-10 minutes* \nPot Life \n2 minutes* \nPeak Exothermic \nCuring Temperature \n140 °F (60 °C)* \nDurometer Hardness \n87D \n* Optimum mixing ratio \nGHS07 \nGHS02 \n\n\nPage 2\nwww.alliedhightech.com \nAllied High Tech Products, Inc. \nCall for more information: 800.675.1118 \n \n2 of 2 \nTable 1: QuickSet Standard Curing Parameters \nMount Size \nCure Time \n(Minutes)* \nMixing Ratio \nWeight (g)** \n \nHardener \n \n1"/ 25 mm \n6-8 \n2:1 \n9.69 \n4.85 \n \n1.25"/ 32 mm \n6-8 \n2:1 \n15.17 \n7.58 \n \n1.5"/ 38-40 mm \n6-8 \n2:1 \n21.83 \n10.92 \n \n2"/ 50 mm \n6-8 \n2:1 \n30.56 \n15.28 \n* Mixing ratio and room temperature will influence performance and the data in the table above; if mixture of \ncomponents by weight is not done precisely, these numbers will also vary. Place large molds into a shallow bath of \nwater to reduce exothermic heat. \n** Per one (1) mount \nPowder\n