HOT RELEASE SPRAY: SAFETY DATA SHEET

Refer to the original PDF for tables, figures and page layout.

Page 1
 
Page 1/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
59.1.0
* 1 Identification
· Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
· Part number: 200-10004
· Details of the supplier of the safety data sheet
· Manufacturer/Supplier:
Allied High Tech Products Inc.
16207 Carmenita Road
USA-Cerritos, CA, 90703
USA
info@alliedhightech.com
· Information department: Product safety department
· Emergency telephone number:
During normal opening times: +1 (310) 635-2466
Chemtrec: +1 (202) 483-7616
2 Hazard(s) identification
· Classification of the substance or mixture
GHS02 Flame
Flammable Aerosols 2
H223
Flammable aerosol.
GHS04 Gas cylinder
Gases under Pressure - Compressed gas
H280
Contains gas under pressure; may explode if heated.
GHS08 Health hazard
Toxic to Reproduction 1B
H360
May damage fertility or the unborn child.
Specific Target Organ Toxicity - Repeated Exposure 2 H373
May cause damage to organs through prolonged or repeated exposure.
GHS07
Acute Toxicity - Dermal 4
H312
Harmful in contact with skin.
Skin Irritation 2
H315
Causes skin irritation.
Eye Irritation 2A
H319
Causes serious eye irritation.
Specific Target Organ Toxicity - Single Exposure 3
H335-H336 May cause respiratory irritation. May cause drowsiness or dizziness.
· Label elements
· GHS label elements The product is classified and labeled according to the Globally Harmonized System (GHS).
(Contd. on page 2)


Page 2
Page 2/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 1)
59.1.0
· Hazard pictograms
GHS02
GHS04
GHS07
GHS08
· Signal word Danger
· Hazard-determining components of labeling:
1-bromopropane
Distillates (petroleum), hydrotreated light
· Hazard statements
Flammable aerosol.
Contains gas under pressure; may explode if heated.
Harmful in contact with skin.
Causes skin irritation.
Causes serious eye irritation.
May damage fertility or the unborn child.
May cause respiratory irritation. May cause drowsiness or dizziness.
May cause damage to organs through prolonged or repeated exposure.
· Precautionary statements
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
Do not spray on an open flame or other ignition source.
Pressurized container: Do not pierce or burn, even after use.
Do not breathe dust/fume/gas/mist/vapors/spray.
Wash contaminated body parts thoroughly after handling.
Use only outdoors or in a well-ventilated area.
Wear eye protection / face protection.
Use personal protective equipment as required.
If on skin: Wash with plenty of soap and water.
IF INHALED: Remove person to fresh air and keep comfortable for breathing.
If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
IF exposed or concerned: Get medical advice/attention.
Call a poison center/doctor if you feel unwell.
If skin irritation occurs: Get medical advice/attention.
Take off contaminated clothing and wash it before reuse.
If eye irritation persists: Get medical advice/attention.
Store in a well-ventilated place. Keep container tightly closed.
Store locked up.
Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.
Dispose of contents/container in accordance with local/regional/national/international regulations.
3 Composition/information on ingredients
· Chemical characterization: Mixtures
· Description: Mixture of the substances listed below with nonhazardous additions.
· Hazardous components and components with occupational exposure limits:
106-94-5 1-bromopropane
 Flammable Liquids 2, H225;
 Carcinogenicity 2, H351; Toxic to Reproduction 1B, H360; Specific Target
Organ Toxicity - Repeated Exposure 2, H373;
 Skin Irritation 2, H315; Eye Irritation 2A, H319; Specific Target
Organ Toxicity - Single Exposure 3, H335-H336
75-85%
68476-86-8 Petroleum gases, liquefied, sweetened
 Flammable Gases 1, H220;
 Gases under Pressure - Compressed gas, H280;
 Germ Cell Mutagenicity 1B,
H340; Carcinogenicity 1A, H350
8-15%
(Contd. on page 3)


Page 3
Page 3/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 2)
59.1.0
64742-47-8 Distillates (petroleum), hydrotreated light
 Flammable Liquids 3, H226;
 Aspiration Hazard 1, H304;
 Specific Target Organ Toxicity - Single
Exposure 3, H336
1-5%
· Non-hazardous components:
Proprietary Ingredient
1-5%
4 First-aid measures
· Description of first aid measures
· General information:
Immediately remove any clothing soiled by the product.
Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.
· After inhalation: In case of unconsciousness place patient stably in side position for transportation.
· After skin contact: Immediately wash with water and soap and rinse thoroughly.
· After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
· After swallowing: If symptoms persist consult doctor.
· Information for doctor:
· Most important symptoms and effects, both acute and delayed
Headache
Dizziness
Nausea
Dermatitis
Eye irritation
· Indication of any immediate medical attention and special treatment needed No further relevant information available.
5 Fire-fighting measures
· Extinguishing media
· Suitable extinguishing agents: Use fire fighting measures that suit the environment.
· Special hazards arising from the substance or mixture During heating or in case of fire poisonous gases are produced.
· Advice for firefighters
· Protective equipment: Wear fully protective suit.
6 Accidental release measures
· Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Ensure adequate ventilation
Keep away from ignition sources
· Environmental precautions: No special measures required.
· Methods and material for containment and cleaning up:
Dispose contaminated material as waste according to section 13.
Ensure adequate ventilation.
· Reference to other sections
See Section 7 for information on safe handling.
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.
7 Handling and storage
· Handling:
· Precautions for safe handling
Protect from heat and direct sunlight.
Ensure proper ventilation/exhaustion at workplaces.
Open and handle receptacle with care.
· Information about protection against explosions and fires:
Keep ignition sources away - Do not smoke.
Keep respiratory protective device available.
(Contd. on page 4)


Page 4
Page 4/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 3)
59.1.0
· Conditions for safe storage, including any incompatibilities
· Storage:
· Requirements to be met by storerooms and receptacles: Observe official regulations on storing packagings with pressurized containers.
· Information about storage in one common storage facility: Not required.
· Further information about storage conditions:
Keep receptacle tightly sealed.
Store receptacle in a well ventilated area.
· Specific end use(s) No further relevant information available.
8 Exposure controls/personal protection
· Additional information about design of technical systems: No additional data. See 7.
· Control parameters
· Components with limit values that require monitoring at the workplace:
The following constituent is the only constituent of the product which has a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
106-94-5 1-bromopropane
TLV Long-term value: 0.1 ppm
A3
· Exposure controls
· Personal protective equipment:
· General protective and hygienic measures:
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing.
Wash hands before breaks and at the end of work.
Store protective clothing separately.
Avoid contact with the eyes and skin.
· Breathing equipment: Use suitable respiratory protective device when high concentrations are present.
· Protection of hands:
Protective gloves
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer
to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance
and has therefore to be checked prior to the application.
· Eye protection:
Safety glasses
Tightly sealed goggles
9 Physical and chemical properties
· Information on basic physical and chemical properties
· General Information
· Appearance:
Form:
Aerosol
Color:
White
· Odor:
Mild
(Contd. on page 5)


Page 5
Page 5/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 4)
59.1.0
· Odor threshold:
Not determined.
· pH-value:
Not determined.
· Change in condition
Melting point/Melting range:
<-45 °C (<-49 °F)
Boiling point/Boiling range:
39-87 °C (102.2-188.6 °F)
· Flash point:
Not applicable, as aerosol.
· Flammability (solid, gaseous):
Not applicable.
· Auto igniting:
490 °C (914 °F)
· Decomposition temperature:
Not determined.
· Ignition temperature:
Product is not selfigniting.
· Danger of explosion:
Not determined.
· Explosion limits:
Lower:
Not determined.
Upper:
Not determined.
· Vapor pressure at 20 °C (68 °F):
78.7 hPa (59 mm Hg)
· Vapor pressure at 50 °C (122 °F):
500 hPa (375 mm Hg)
· Density:
Not determined.
· Bulk density:
1 kg/m³
· Relative density
Not determined.
· Vapor density
Not determined.
· Evaporation rate
Not applicable.
· Solubility in / Miscibility with
Water:
Not miscible or difficult to mix.
· Partition coefficient (n-octanol/water): Not determined.
· Viscosity:
Dynamic:
Not determined.
Kinematic:
Not determined.
· Solvent content:
VOC content:
0.91-4.55 %
Solids content:
0.0 %
· Other information
No further relevant information available.
10 Stability and reactivity
· Reactivity No further relevant information available.
· Chemical stability
· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.
· Possibility of hazardous reactions No dangerous reactions known.
· Conditions to avoid No further relevant information available.
· Incompatible materials: No further relevant information available.
· Hazardous decomposition products: No dangerous decomposition products known.
(Contd. on page 6)


Page 6
Page 6/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 5)
59.1.0
11 Toxicological information
· Information on toxicological effects
· Acute toxicity:
· LD/LC50 values that are relevant for classification:
106-94-5 1-bromopropane
Inhalative LC50/4 h 253 mg/l (rat)
64742-47-8 Distillates (petroleum), hydrotreated light
Dermal
LD50
3,160 mg/kg (rabbit)
· Primary chemical irritant effect:
· on the skin: Irritant to skin and mucous membranes.
· on the eye: Irritating effect.
· Sensitization: No sensitizing effects known.
· Additional toxicological information:
Specific Target Organ Toxicity - Single Exposure 3 - Target Organ: central nervous system depression
· Carcinogenic categories
· IARC (International Agency for Research on Cancer)
106-94-5 1-bromopropane
2B
· NTP (National Toxicology Program)
106-94-5 1-bromopropane
R 
· OSHA-Ca (Occupational Safety & Health Administration)
None of the ingredients is listed.
12 Ecological information
· Toxicity
· Aquatic toxicity: No further relevant information available.
· Persistence and degradability No further relevant information available.
· Behavior in environmental systems:
· Bioaccumulative potential No further relevant information available.
· Mobility in soil No further relevant information available.
· Additional ecological information:
· General notes:
Do not allow product to reach ground water, water course or sewage system, even in small quantities.
Danger to drinking water if even extremely small quantities leak into the ground.
· Results of PBT and vPvB assessment
· PBT: Not applicable.
· vPvB: Not applicable.
· Other adverse effects No further relevant information available.
13 Disposal considerations
· Waste treatment methods
· Recommendation: Contact waste processors for recycling information.
· Uncleaned packagings:
· Recommendation: Disposal must be made according to official regulations.
14 Transport information
· UN-Number
· DOT, IMDG, IATA
UN1950
· UN proper shipping name
· DOT
Aerosols, flammable
(Contd. on page 7)


Page 7
Page 7/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 6)
59.1.0
· IMDG
AEROSOLS
· IATA
AEROSOLS, flammable
· Transport hazard class(es)
· DOT
· Class
2.1 Gases
· Label
2.1
· IMDG, IATA
· Class
2.1 Gases
· Label
2.1
· Packing group
· DOT, IMDG, IATA
not regulated
· Environmental hazards:
Not applicable.
· Special precautions for user
Warning: Gases
· Hazard identification number (Kemler code):
- 
· EMS Number:
F-D,S-U
· Stowage Code
SW1 Protected from sources of heat.
SW22 For AEROSOLS with a maximum capacity of 1 litre: Category
A. For AEROSOLS with a capacity above 1 litre: Category B. For
WASTE AEROSOLS: Category C, Clear of living quarters.
· Segregation Code
SG69 For AEROSOLS with a maximum capacity of 1 litre:
Segregation as for class 9. Stow "separated from" class 1 except for
division 1.4.
For AEROSOLS with a capacity above 1 litre:
Segregation as for the appropriate subdivision of class 2.
For WASTE AEROSOLS:
Segregation as for the appropriate subdivision of class 2.
· Transport in bulk according to Annex II of MARPOL73/78 and
the IBC Code
Not applicable.
· Transport/Additional information:
· DOT
· Quantity limitations
On passenger aircraft/rail: 75 kg
On cargo aircraft only: 150 kg
· Limited quantities (LQ)
1L
· Transport category
2 
· Tunnel restriction code
D 
· IMDG
· Limited quantities (LQ)
1L
· Excepted quantities (EQ)
Code: E0
Not permitted as Excepted Quantity
· UN "Model Regulation":
UN 1950 AEROSOLS, 2.1
(Contd. on page 8)


Page 8
Page 8/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 7)
59.1.0
15 Regulatory information
· Safety, health and environmental regulations/legislation specific for the substance or mixture
No further relevant information available.
· Sara
· Section 355 (extremely hazardous substances):
None of the ingredients is listed.
· Section 313 (Specific toxic chemical listings):
106-94-5 1-bromopropane
· TSCA (Toxic Substances Control Act):
All components have the value ACTIVE.
· Hazardous Air Pollutants
106-94-5 1-bromopropane
· Proposition 65
· Chemicals known to cause cancer:
106-94-5 1-bromopropane
· Chemicals known to cause reproductive toxicity for females:
106-94-5 1-bromopropane
· Chemicals known to cause reproductive toxicity for males:
106-94-5 1-bromopropane
· Chemicals known to cause developmental toxicity:
106-94-5 1-bromopropane
· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.
16 Other information
To the best of our knowledge, the information contained herein is accurate. However, it does not describe a guarantee of product properties
and does not establish a contractual legal relationship.
· Department issuing SDS: Technical Services
· Contact: Pablo Mendoza
· Last revision / supersedes version: 06/01/2024 / 1.0
· Supersedes date: 10/10/2023
· Abbreviations and acronyms:
ADR: Accord relatif au transport international des marchandises dangereuses par route (European Agreement Concerning the International Carriage of Dangerous Goods by
Road)
IMDG: International Maritime Code for Dangerous Goods
DOT: US Department of Transportation
IATA: International Air Transport Association
EINECS: European Inventory of Existing Commercial Chemical Substances
ELINCS: European List of Notified Chemical Substances
CAS: Chemical Abstracts Service (division of the American Chemical Society)
VOC: Volatile Organic Compounds (USA, EU)
LC50: Lethal concentration, 50 percent
LD50: Lethal dose, 50 percent
PBT: Persistent, Bioaccumulative and Toxic
vPvB: very Persistent and very Bioaccumulative
OSHA: Occupational Safety & Health
TLV: Threshold Limit Value
PEL: Permissible Exposure Limit
REL: Recommended Exposure Limit
Flammable Gases 1: Flammable gases – Category 1
Flammable Aerosols 2: Aerosols – Category 2
Gases under Pressure - Compressed gas: Gases under pressure – Compressed gas
Flammable Liquids 2: Flammable liquids – Category 2
Flammable Liquids 3: Flammable liquids – Category 3
Acute Toxicity - Dermal 4: Acute toxicity – Category 4
Skin Irritation 2: Skin corrosion/irritation – Category 2
Eye Irritation 2A: Serious eye damage/eye irritation – Category 2A
(Contd. on page 9)


Page 9
Page 9/9
Safety Data Sheet
acc. to OSHA HCS
Printing date 07/02/2024
Last revision 06/01/2024
Version 2.0
Product name: Mold Release Spray, Aerosol Spray (Hot Mouting)
(Contd. of page 8)
59.1.0
Germ Cell Mutagenicity 1B: Germ cell mutagenicity – Category 1B
Carcinogenicity 1A: Carcinogenicity – Category 1A
Carcinogenicity 2: Carcinogenicity – Category 2
Toxic to Reproduction 1B: Reproductive toxicity – Category 1B
Specific Target Organ Toxicity - Single Exposure 3: Specific target organ toxicity (single exposure) – Category 3
Specific Target Organ Toxicity - Repeated Exposure 2: Specific target organ toxicity (repeated exposure) – Category 2
Aspiration Hazard 1: Aspiration hazard – Category 1
· * Data compared to the previous version altered.